BIOENERAY XL2™ Plasma Tube Unit +
Your Frequency Generator/Instrument -
Operating Instructions:

CAUTION - Your BIOENERAY XL2™ Plasma Tube Unit can radiate Frequencies, which tend to dissolve Blood Clots, and so it should NOT be used in the following circumstances:
(1) on anyone, who has a Phlebitis.
(2) on anyone, who has Thrombosis, especially using 10 Hz..
(3) on anyone, who has NOT had several weeks of GOOD Healing after Major or Minor Surgery.
(4) on anyone, who has suffered a Stroke, which was caused by an Artery rupturing in the Brain.

and/or in the following circumstances according to F.D.A. Regulations:
(1) on anyone, who is Pregnant or is suspected of being Pregnant.
(2) on anyone, who has Epilepsy &/or Convulsions.
(3) on anyone, who has a Psychotic Disorder.
(4) on anyone, who has Glaucoma.
(5) on anyone, who has Back Problems.
(6) on anyone, who has Hypertension with resistance to Medical Therapy.
(7) on anyone, who has Heart Problems, especially using 1 Hz..
(8) on anyone, who wears a Pacemaker &/or a Defibrillator, especially using 1 Hz..
(9) on anyone, who has good-quality and Malignant Neoplasms.
(10) on anyone, who has a violation of Blood Coagulability.
(11) on anyone, who has inherent Pathologies of the Central Nervous System.
(12) on anyone, who has a condition of acute Mental Excitation (hyperphrenia) or Intoxication.

Preliminary Comments:

1) Please remove ALL Metal Ornaments/Jewelry, Watches, Glasses, Pager and Cellphone (and any other devices generating electromagnetic radiations), before doing the following procedure.

2) Please wear Clothes made from NATURAL Fabric(s).

3) Please be SURE that you've read and that you understand your own Frequency Generator/Instrument - Operating Instructions, before proceeding with Operating Steps 1 - 16.

4) Your Frequency Generator/Instrument should be preprogrammed with the REQUIRED Specific Frequencies and Time Periods, if a Programming Function is available, before proceeding with Operating Steps 1 - 16.

5) Please ELIMINATE Operating Steps 1 - 7 (see below), once they are initially COMPLETED, if you're going to use your BIOENERAY XL2™ Plasma Tube Unit on a REGULAR basis.

6) Please pay SPECIAL attention to the RED NOTE in Step 13 (see below) and the NOTES, which are right after Operating Steps 1, 3, 5, 6, 9 & 11.

7) Please place your Power Supply #1 (blue/white metal cabinet) within 1 ft. of the rear of your Glass Plasma Tube & Stand/Holder, but at LEAST 3 ft. away from your Power Supply #2 (dark gray metal cabinet) and at least 3 ft. away from your Frequency Generator/Instrument.

8) Please place your Power Supply #2 (dark gray metal cabinet) at LEAST 3 ft. away from your Body, during your EXPERIMENTAL Treatment Session.
NOTE: Your Power Supply #2 (dark gray metal cabinet) emits a 60 Hz. Electromagnetic Field, which is a Frequency, that can ADVERSELY affect your Health, especially when you're SERIOUSLY ILL.

9) Please place your Frequency Generator/Instrument on either a Plastic or a Wood Table and your BIOENERAY XL2™ Plasma Tube Unit on various shelves of a Book Shelf, so that you can use your BIOENERAY XL2™ Plasma Tube Unit for the top to the bottom of your Body, if NEEDED.
NOTE: Whatever you use, there should be FEW, if ANY, Metal Parts involved.

10) Please clean your Glass Plasma Tube, if it has Film/Haze on it, with an ammonia-based Glass Cleaner, when it has COOLED DOWN and is NOT being used.

11) Please hold onto the Jack &/or the Plug, rather than holding onto the Cable, when you are connecting or disconnecting Cables, pertaining to your BIOENERAY XL2™ Plasma Tube Units &/or your Frequency Generator/Instrument.

12) Please lift your Power Supply #1 (blue/white metal cabinet), when moving it to another location, because sliding your Power Supply #1 (blue/white metal cabinet) could DISPLACE it's Rubber Feet.

13) Please REPLACE a Metal Amplitude/Intensity Knob, with a Plastic Knob (or wear a glove), if applicable.
NOTE: The High Voltage Electrical Field, being generated, will flow from your Body into a Metal Knob and then into your Frequency Generator/Instrument, causing Digital Readout PROBLEMS and possible internal DAMAGE!

14) Please do NOT operate your BIOENERAY XL2™ Plasma Tube Unit CONTINUOUSLY for MORE than 3 hours, because the Power Transistor and Ignition Coils in your Power Supply #1 (blue/white metal cabinet) could OVERHEAT EXCESSIVELY!
NOTE: If you allow your Power Supply #1 (blue/white metal cabinet) to COOL DOWN for 15 minutes, you may then use it again CONTINUOUSLY for another 3 hours.

15) Please do NOT operate below 50 Hz. or use the "PULSE" Function (if applicable) below 100 Hz. on your Frequency Generator/Instrument, because the Power Transistor in your Power Supply #1 (blue/white metal cabinet) will OVERHEAT EXCESSIVELY and then eventually BURN-OUT!

16a) Please follow Step 16b below, if you're SERIOUSLY-ILL, instead of this Step 16a. Otherwise, please do your EXPERIMENTAL Treatment Session once per day (morning or evening) for a TOTAL EXPERIMENTAL Treatment Time per Session of 10 mins.. Perform your EXPERIMENTAL Treatments for 6 consecutive days, and then NONE on the 7th day. REPEAT the SAME Cycle for 2 MORE weeks and then DISCONTINUE for 1 week. If the DESIRED Results have NOT been achieved, during the 1 week break, then REPEAT your EXPERIMENTAL Treatments, and CONTINUE them until the DESIRED Results are achieved.
NOTE: If you're ABLE, you should INCREASE your TOTAL EXPERIMENTAL Treatment Time on the 2nd Week to 20 mins. and on the 3rd week to 30 mins..

16b) Please do your EXPERIMENTAL Treatment Session, 2 times per day (morning and evening), if you're SERIOUSLY-ILL, starting out with 1-3 mins. per Frequency, and NOT EXCEEDING 10 minutes of TOTAL EXPERIMENTAL Treatment Time each Session. Do your EXPERIMENTAL Treatment Session EVERY 3 days (i.e. - Day Nos. 1, 4, 7, 10, 13, 16, 19 & 22) and then DISCONTINUE for 7 days. If you have NOT achieved the DESIRED Results, during the 1 week BREAK, then REPEAT your EXPERIMENTAL Treatments, and CONTINUE them, until the DESIRED Results are ACHIEVED.
NOTE: If you're ABLE, you should INCREASE your TOTAL EXPERIMENTAL Treatment Time per day on the 2nd Week to 30 mins..

17) Your EXPERIMENTAL Treatment Sessions should ONLY be STOPPED TEMPORARILY, if UNDUE DISCOMFORT is experienced, during the Detoxification Process. If DETOXIFICATION does become TOO UNCOMFORTABLE or ANY ADVERSE Reactions occur, then please DISCONTINUE &/or MODIFY your EXPERIMENTAL Treatment Sessions, and if possible, please try to continue your EXPERIMENTAL Treatment Sessions. Please drink 8 oz. of Activated Charcoal Slurry 6-8 times/day to ADSORB DEAD Pathogens, TOXIC Organic &/or Inorganic Chemicals, that being DETOXED from your Body. Please see Final Comments below) also.

18) Please see Setup Diagram and Setup Diagram 2, before proceeding with Operating Steps 1 - 12.

Operating Steps:

1) Plug your Power Supply #2 (dark gray metal cabinet) into a HIGH-Quality Surge Suppressor Power Strip (i.e. - TrippLite - 800+ joules), thus ensuring it's PROTECTION.
NOTE: Your Frequency Generator/Instrument (and NO other Electrical/Electronic Device) should also be plugged into this HIGH Quality Surge Suppressor Power Strip. In fact, please do NOT plug ANY other Electrical/Electronic Device into the SAME A.C. Wall Outlet into which this Surge Suppressor Power Strip has been plugged.

2) Push the 2 - stacking-type Gold Banana Plugs (Red & Black), which are connected to one end of the 6 ft. Cable #2, that has 2 - stacking-type Banana Plugs connected to the other end, into the corresponding color (Red & Black) Banana Jacks on the Rear Panel (right corner) of your Power Supply #2 (dark gray metal cabinet).
NOTE: The Tenma 12 Volt Power Supply has the Red & Black Banana Jacks on the Front Panel (left corner).

3) Push the 2 - stacking-type Gold Banana Plugs (Red & Black), which are connected to other end of the 6 ft. Cable #2 into the corresponding color (Red & Black) Banana Jacks (12 VOLTS INPUT) on the Front Panel (left side) of your Power Supply #1 (blue/white metal cabinet).
NOTE: DO NOT plug these 2 - stacking-type Gold Banana Plugs (Red & Black) into the Red & Black Banana Jacks on your Frequency Generator/Instrument, because the 12 Volts will BURN-OUT it's Output Transistors!!

4) Connect the BNC Plug, which is connected to one end of the 6 ft. Cable #1, which has the 2 - flexible Banana Plugs (or BNC Plug) connected to the other end, to the BNC Jack (PULSE INPUT) on the Front Panel (tight side) of your Power Supply #1 (blue/white metal cabinet).
NOTE: Match the 2 - Slots on the BNC Plug with the 2 - Pins on the BNC Jack and push the BNC Plug 'IN' and then turn the BNC Plug clockwise 1/4 turn.

5) Push the Black Banana Plug, which is connected to the other end of the 6 ft. Cable #1 into the Black Banana Jack, which is on the Front Panel of your Frequency Generator/Instrument. Then push the Red Banana Plug into the Red Banana Jack, which is also on the Front Panel of your Frequency Generator/Instrument.
Or if there is a BNC Plug connected to the other end of your particular 6 ft. Cable #1, then connect it to the BNC Jack on the Front Panel of your particular Frequency Generator/Instrument.
NOTE: DO NOT plug these Banana Plugs (Red & Black) into the Red & Black Banana Jacks on your Power Supply #2 (dark gray metal cabinet), because the 12 Volts will BURN-OUT the Power Transistor in your Power Supply #1 (blue/white metal cabinet)!!

6) Push the 2 - Heavy-Duty Banana Plugs (Red & Black), which are connected to ends of the High Voltage Wires (thick & black), that have their other ends connected to the ends of your Glass Plasma Tube, FIRMLY into the corresponding color (Red & Black) Banana Jacks, which are on the middle of the Rear Panel of your Power Supply #1 (blue/white metal cabinet).
NOTE: Please be SURE that your Glass Plasma Tube is connected to your Power Supply #1 (blue/white metal cabinet), while operating your BIOENERAY XL2™ Plasma Tube Unit, otherwise the EXCESSIVE High Voltage, being generated, will ARC-OVER to Ground, causing Components in your Frequency Generator/Instrument to BURN-OUT, plus the SPECIAL High Voltage Coils in your Power Supply #1 (blue/white metal cabinet) will also eventually BURN OUT!
PLEASE DO NOT TOUCH with your Fingers or PROBE with a Metal Object, such as a Screwdriver these Banana Jacks, since you will receive a VERY SEVERE SHOCK!

7) Adjust the Amplitude/Intensity on your Frequency Generator/Instrument to the setting of '0', if it isn't ALREADY at that particular setting.

8) Flip/Rock/Turn the POWER Switch on your Frequency Generator/Instrument to the "ON" Position.

9) Rock the Power Switch on your Power Supply #2 (dark gray metal cabinet) to turn it's Power "ON".
NOTE: Please notice that the 2" Cooling Fan on the top of your Power Supply #1 (blue/white metal cabinet) is running and that your Glass Plasma Tube is NOT yet glowing. If your Glass Plasma Tube is GLOWING and the Amplitude Control Knob is set at '0' on your Frequency Generator/Instrument, then you've got a PROBLEM with your Power Supply #1 (blue/white metal cabinet) and it NEEDS to be serviced! Please email and/or call Tom Harrelson (614/237-8708).

10) Program your particular Frequency Generator/Instrument to generate the desired SPECIFIC Frequencies, after reading your Operating Instructions and if applicable, START the Program on your Frequency Generator/Instrument. Also you must set your Frequency Generator/Instrument to operate at a 50% Duty Cycle for the HIGHEST Electrostatic Field!
NOTE: You can also use each of the following Frequencies for 3-5 mins.: 64 (oxygen/ozone), 66.5 Hz. (universal pathogen), 528 Hz. followed by 15 Hz. (DNA repair), 727.5 Hz. (universal Rife) and 5,000 Hz. + 10,000 Hz. (cell regeneration).

11) Turn the Amplitude/Intensity Knob on your Frequency Generator/Instrument SLOWLY clockwise from the Setting of '0', until you reach a Setting, where you obtain a Plasma Glow, that doesn't CHANGE in Brightness, when turning the Knob SLIGHTLY HIGHER.
NOTE: DO NOT turn the AMPLITUDE Control Knob past this Setting at this FIRST Frequency, since it may cause OVERHEATING and eventual BURNOUT of the Power Transistor in your Power Supply #1 (blue/white metal cabinet). You can CHANGE this Setting SLIGHTLY, if, when your Frequency Generator/Instrument is generating another Frequency, there is NO or VERY LOW Plasma Glow observed.

12) Place the front length of your Glass Plasma Tube, so that it is PARALLEL with your Body and 1-3 ft. away from the Area of your Body to be treated. Please be seated, so that your Plasma Tube can now radiate the High Voltage Electrical Field at the SPECFIC Pulse Frequency towards and through your Body.
NOTE: Please see Setup Diagram 2. You don't have to be EXACTLY pointed towards the Area, because the Energy Output from your Glass Plasma Tube RADIATES towards your Body. Children and Animals should be 3-6 ft. away from the Glass Plasma Tube.

When you've COMPLETED your EXPERIMENTAL Pulsed High Voltage Electrical Field Treatment, then please follow Operating Steps 13 - 16 sequentially.

13) Rock the Power Switch on your Power Supply #2 (dark gray metal cabinet) again to turn the Power "OFF".

14) Turn the Amplitude/Intensity Knob on your Frequency Generator/Instrument counter-clockwise to a Setting of 0.

15) Flip/Rock/Turn the Power Switch on your Frequency Generator/Instrument to the "OFF" Position.

16) Rock the Power Switch on the Power Strip to turn the Power "OFF" COMPLETELY to your Frequency Generator/Instrument and your BIOENERAY XL2™ Plasma Tube Units.

Final Comments:

1) Drink One 8 oz. glass of PURE Water with a SUPERIOR Probiotic Product daily to replenish your FRIENDLY Intestinal Bacteria.
NOTE: This Probiotic Product is AVAILABLE from Health Food Stores or an Online Websites.

2) Drink 6-8 Glasses of Activated Charcoal Slurry (1 tsp./8 oz. - pure water) daily to ADSORB the HIGHER-than-normal amounts of TOXINS, which are NOW in your Bloodstream.
NOTE: Activated Charcoal Powder is AVAILABLE from Tom Harrelson/TOTAL HEALTH Associates/P.O. Box 9872/Columbus, OH 43209-00872/614-237-8708.

3) Take a SUPERIOR Laxative & Colon Cleanser (i.e. - Dr. Schulze's Intestinal Formulas #1 & #2) daily also (use as directed) to move the Bowels and ADSORB the TOXINS from the Intestines.
NOTE: Dr. Schulze's Intestinal Formulas #1 & #2 are AVAILABLE from American Botanical Pharmacy/800-437-2362.

Revised 9/4/04