BIOPHOTON CLUSTER™ +
Your Frequency Instrument -
Operating Instructions

DISCLAIMER: Your BIOPHOTON CLUSTER™ is to be used "FOR EXPERIMENTAL PURPOSES ONLY".

Preliminary Comments:

1. Your BIOPHOTON CLUSTER™ radiates a SOLID RED (near-infrared) Wide Oval-Shaped Beam, when being powered by the 4 - 1.5 Volt Batteries in series, that are mounted inside of it's Handle/Box. This SOLID RED (near-infrared) Wide Oval-Shaped Beam is then shined onto a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).

2. Your BIOPHOTON CLUSTER™ radiates a PULSED RED (near-infrared) Wide Oval-Shaped Beam, when being pulsed by your own Frequency Instrument at a SPECIFIC Frequency/Pulse Rate. This PULSED RED (near-infrared) Wide Oval-Shaped Beam is then shined onto a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).

3. Please follow these Steps CAREFULLY, ensuring EFFICIENT Operation of and receiving EFFICACIOUS Results from your BIOPHOTON CLUSTER™.

4. Operating Steps 1 & 2 can be ELIMINATED, if your BIOPHOTON CLUSTER™ is being used with your own Frequency Instrument on a REGULAR basis.

Operating Steps:

1. Push the BNC Plug, which is connected to one end of the 25' Coiled-Cable, that has a 1/8" Jack connected to the other end, into the BNC Jack, which is usually labeled 'OUTPUT' and which is usually on the Front Panel of your own Frequency Instrument.

2. Push the 1/8" Plug, which is connected to the Short Cable, that is connected to the BIOPHOTON CLUSTER™, into the 1/8" Jack, which is conected to the other end to the 25' Coiled-Cable.

3. Flip the minature Toggle Switch on top of your BIOPHOTON CLUSTER™ Right to the 'SOLID' Position, if your BIOPHOTON CLUSTER™ is going to be operated in the SOLID/CONTINUOUS (sedation - pain & swelling) Beam Mode.
NOTE: A SOLID RED Wide Oval-Shaped Beam should NOW be shining from the top front of your BIOPHOTON CLUSTER™, and if it is, then proceed to Step 4. But if a SOLID RED Wide Oval-Shaped Beam is NOT shining from the top front of your BIOPHOTON CLUSTER™, then please check your Batteries, Cables and Connectors. If they are NOT the PROBLEM, then please contact me (Tom) at 614/237-8708 or tharrels@hotmail.com.
Pull the 1/8" Plug out, which is connected to your BIOPHOTON CLUSTER™, if you want to to be ABLE to use your BIOPHOTON CLUSTER™ in the SOLID/CONTINUOUS Beam Mode ONLY and WITHOUT the 25' Coiled-Cable and your own Frequency Instrument.

4. Flip the minature Toggle Switch on the top of your BIOPHOTON CLUSTER™ past the middle 'OFF' Postion to the left 'PULSE' Position, if you want to use your BIOPHOTON CLUSTER™ in the PULSED (stimulation - cuts & wounds +) Beam Mode.

5. See your own Frequency Instrument - Operating Instructions.
NOTE: Please set the Duty Cycle Control to 50%, if applicable, thus ensuring EFFICIENT and EFFECTIVE Results.

6. Turn the Amplitude Control on your own Frequency Instrument CLOCKWISE to a Setting, that is SLIGHTLY DIMMER, than the Light Output, whenever operating in the 'SOLID' Mode.
NOTE: A PULSED (SOLID above 50 Hz.) RED Wide Oval-Shaped Beam should NOW be shining from the top front of your BIOPHOTON CLUSTER™, and if it is, then proceed to Step 7. But if a PULSED (SOLID above 50 Hz.) RED Wide Oval-Shaped Beam is NOT shining from the top front of your BIOPHOTON CLUSTER™, then please check your Batteries, Cables and Connectors. If they are NOT the PROBLEM, then please contact me (Tom) at 614/237-8708 or tharrels@hotmail.com.

7. "PAINT" a LARGE (more than 4") affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.) by tracing 2-3" CLOCKWISE Circles with the RED Wide Oval-Shaped Beam.
NOTE: The Rate, at which you trace those Circles, can be varied from SLOW to VERY RAPID. CHRONIC Condtions usually respond BEST to a RAPID Rate, whereas ACUTE Condtions usually respond BEST to a SLOWER Rate.

8. Perform this Procedure on each AFFECTED Body Area, that NEEDS to be treated for 2-5 minutes.
NOTE: Can be done up to 3 times per day, and each Body Area should ONLY receive a MAXIMUM Treatment Time per Day of 10 mins. (acute conditions) and 15 mins. (chronic conditions).

9. If you're using MORE than one Frequency/Pulse Rate, then divide the TOTAL Treatment Time of 10 mins. (acute conditions) and 15 mins. (chronic conditions) by the number of Frequencies/Pulse Rates to obtain the amount of Time for each Frequency/Pulse Rate. Also see Frequency & Duration Of Treatments.

10. When you're FINISHED using your BIOPHOTON CLUSTER™ in the SOLID/CONTINUOUS Beam Mode, flip the minature Toggle Switch on the top of your BIOPHOTON CLUSTER™ to the middle 'OFF' Position.
NOTE: Eventhough the HIGH-Intensity LEDs in your BIOPHOTON CLUSTER™ draws a LOW Amount of Current, you should turn your Batteries inside of it's Handle/Box.

11. When you're FINISHED using your BIOPHOTON CLUSTER™ in theither Beam Mode, turn your own Frequency Instrument "OFF".

12. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments until the DESIRED Results are achieved.

Final Comments:

1. DISCONTINUE &/or MODIFY the EXPERIMENTAL Biophoton Light Therapy Treatment with your BIOPHOTON CLUSTER™, if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (2-3 days), please continue your EXPERIMENTAL Light Treatment.

2. Try using 3300 Hz., operating in the PULSE Beam Mode, if while operating in the SOLID Beam Mode, the 4 - 1.5 Volt Batteries go DEAD, or also if you want to experiment with a NEW Frequency.

3. Try experimenting with 47 Hz., 66.5 Hz., 528 Hz. &/or 727.5 Hz. as UNIVERSAL Healing Frequencies, while operating in the PULSED Beam Mode.

4. Try using 5.9 Hz. & 18 Hz., while operating in the PULSED Beam Mode, as Acupuncture Energy Field Disturbance Frequencies, if Results are NOT being achieved, because Scar Tissue &/or Adhesions are involved.

5. Monitor the duration of the EXPERIMENTAL Biophoton Light Therapy Treatments with your BIOPHOTON CLUSTER™ for each SPECIFIC Frequency/Pulse Rate with a Digital Timer (i.e. - Radio Shack No. 63-878 or 63-917).

6. Clean the Lens on the tip of your BIOPHOTON CLUSTER™ once per week, or as NEEDED, using a Plastic Lens Cleaner (i.e. - Opti-Mist) to ENSURE that the MAXIMUM Wide Oval-Shaped Beam of RED Light is being emitted.

Revised 1/11/08