BIOPHOTON WAND™ - Operating Instructions

DISCLAIMER: Your BIOPHOTON WAND™ is to be used "FOR EXPERIMENTAL PURPOSES ONLY".

Preliminary Comments:

1. Your BIOPHOTON WAND™ radiates a SOLID or PULSED RED (near-infrared) Beam. If it's being used in the PULSED Beam Mode, your BIOPHOTON WAND™ is being pulsed by a SPECIFIC Frequency/Pulse Rate and in either Beam Mode is also being shined on a SPECIFIC Acupuncture Point, Trigger (center of pain) Point &/or Reflex Point or onto a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).

2. Please follow these Steps CAREFULLY to ENSURE EFFICIENT Operation of and EFFICACIOUS Results from your BIOPHOTON WAND™.

3. Steps 1 - 4 can be ELIMINATED, if you're going to use your BIOPHOTON WAND™ with your WAVETEK Frequency Generator on a REGULAR basis.

Operating Steps:

1. Push the BNC Plug, which is connected to one end of the 12" Cable, that has a 1/8" Plug connected to the other end, into the BNC Jack at the bottom right side of the front panel of your WAVETEK Frequency Generator.

2. Push the 1/8" Plug, which is connected to the other end of this 12" Cable, that has the BNC Plug now connected to the BNC Jack on your WAVETEK Frequency Generator, into the 1/8" Jack, which is labeled 'INPUT', on the left end of the Control Box of your BIOPHOTON WAND™.

3. Push the 1/4" Plug, which is connected to one end of the 12 ft. Coiled-Cable, that has a 1/8" Plug connected to the other end, into the 1/4" Jack, which is labeled 'OUTPUT', on the right end of the Control Box of your BIOPHOTON WAND™ .

4. Push the 1/8" Plug, which is connected to other end of the 12 ft. Coiled-Cable, that has the 1/4" Plug now connected to the 1/4" 'OUTPUT' Jack, into the 1/8" Jack on one end of your BIOPHOTON WAND™.

5a. Flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ to the 'SOLID' Position, if you want to operate your BIOPHOTON WAND™ in the SOLID/CONTINUOUS (sedation - pain & swelling) Beam Mode. Now proceed to Step 6a or 6b.
NOTE: There should be a SOLID RED Beam shining from the tip of your BIOPHOTON WAND™, and if so, it's READY to be used. But if there is NOT a SOLID RED Beam shining from the tip of your BIOPHOTON WAND™, then please check your Cables and Connectors. Otherwise please contact me (Tom) at 614/237-2590 or tharrels@hotmail.com.

When your BIOPHOTON WAND™ is in the SOLID/CONTINUOUS Beam Mode, it is being powered by a 3 Volt Lithium Battery in series with a 10 ohm Resistor, which are mounted inside of the Control Box of your BIOPHOTON WAND™.

You can also operate your BIOPHOTON WAND™ as a STAND-ALONE Unit in the SOLID/CONTINUOUS Beam Mode by pulling the 1/8" Plug out, that's connected into the 1/8" Jack ('INPUT'), on the left end of the Control Box of your BIOPHOTON WAND™.

5b. Flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ to the 'PULSE' Position, if you want to operate your BIOPHOTON WAND™ in the PULSED Beam Mode (stimulation - cuts & wounds).

5c. Tune to the SPECIFIC Frequency/Pulse Rate on your WAVETEK Frequency Generator.

5d. Turn the Amplitude Control on your WAVETEK Frequency Generator CLOCKWISE to it's MAXIMUM setting.
NOTE: There should be a PULSED (or SOLID above 50 Hz.) RED Beam shining from the tip of your BIOPHOTON WAND™, and if so, it's READY to be used. But if there is NOT a PULSED or SOLID RED Beam shining from the tip of your BIOPHOTON WAND™, then please check your Cables and Connectors. Otherwise please contact me (Tom) at 614/237-2590 or tharrels@hotmail.com.

Notice that the RED Beam, being emitted by your BIOPHOTON WAND™, in the PULSED Beam Mode is DIMMER, than it is when your BIOPHOTON WAND™, is being operated in the SOLID Beam Mode. The reason for this is the Duty Cycle of your WAVETEK Frequency Generator is approximately 80%.

6a. Hold your BIOPHOTON WAND™ like a Pen, pointing it's RED Beam DIRECTLY onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point, &/or Reflex Point at a Distance NOT MORE than 1/4" above or NEXT to the Skin. Move the tip of your BIOPHOTON WAND™ in a SLOW CLOCKWISE Circle, starting about 1" from the Acupuncture Point, Reflex Point or Trigger (center of pain) Point and moving towards the center and then holding it in place for 2-5 mins.
NOTE: The tip of your BIOPHOTON WAND™ can be applied with a GENTLE Pressure onto an Acupuncture Point or Reflex Point for 30-90 secs., providing a ROUGH Diagnostic Technique, since the degree of SENSITIVITY of the Acupuncture Point or Reflex Point will give a relative evaluation of the status of your Health PROBLEM. You will find that as the Condition of your Health PROBLEM IMPROVES, the Acupuncture Point or Reflex Point SENSITIVITY will be REDUCED!

6b. "PAINT" a LARGE (more than 1/4") affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.) by tracing 1" CLOCKWISE Circles with the RED Beam.
NOTE: The Rate, at which you trace those Circles, can be varied from SLOW to VERY RAPID. CHRONIC Condtions usually respond BEST to a RAPID Rate, whereas ACUTE Condtions usually respond BEST to a SLOWER Rate.

7. Perform this Procedure on each Point/Area, that NEEDS to be treated for 2-5 minutes.
NOTE: Can be done up to 3 times per day, and each Point/Area should ONLY receive a MAXIMUM Treatment Time per Day of 10 mins. (acute conditions) and 15 mins. (chronic conditions).

If you're using MORE than One Frequency/Pulse Rate, then divide the TOTAL Treatment Time of 10 mins. (acute conditions) and 15 mins. (chronic conditions) by the number of Frequencies/Pulse Rates to obtain the amount of Time for each Frequency/Pulse Rate. Also see Frequency & Duration Of Treatments.

8a. When you're FINISHED using your BIOPHOTON WAND™ in the SOLID/CONTINUOUS Beam Mode, flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ to the 'PULSE' ('OFF') Position.
NOTE: Eventhough the HIGH-Intensity LED in your BIOPHOTON WAND™ draws ONLY 20 ma. of Current, you should turn your BIOPHOTON WAND™ "OFF" anyhow, thereby CONSERVING the Lithium Battery.

8b. When you're FINISHED using your BIOPHOTON WAND™ in the PULSED Beam Mode, turn your WAVETEK Frequency Generator "OFF".

Final Comments:

1. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments until the DESIRED Results are achieved.

2. DISCONTINUE &/or MODIFY your EXPERIMENTAL Biophoton Light Therapy Treatment, if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (2-3 days), please continue your EXPERIMENTAL Biophoton Light Treatment.

3. Try using 3300 Hz., operating in the PULSE Beam Mode, if while operating in the SOLID Beam Mode, the Lithium Battery goes DEAD, or also if you want to experiment with a NEW Frequency.

4. Try experimenting with 66.5 Hz., 528 Hz. &/or 727.5 Hz. as UNIVERSAL Healing Frequencies, while operating in the PULSE Beam Mode.

5. Try using 5.9 Hz. & 18 Hz., while operating in the PULSE Beam Mode, as Acupuncture Energy Field Disturbance Frequencies, if Results are NOT being achieved and Scar Tissue amp;/or Adhesions are involved.

6. Monitor the duration of your EXPERIMENTAL Biophoton Light Therapy Treatment for each SPECIFIC Frequency/Pulse Rate with a Digital Timer (i.e. - Radio Shack No. 63-878 or 63-917).

7. Clean the Lens on the tip of your BIOPHOTON WAND™ once per week, or as NEEDED, using a Plastic Lens Cleaner (i.e. - Opti-Mist) to ENSURE that the MAXIMUM Beam of RED Light is being emitted.

Revised 1/11/08