BIOPHOTON WAND™ (violet) +
WAVESHAPER Frequency Instrument -
Operating Instructions

DISCLAIMER: Your BIOPHOTON WAND™ (violet) may be used for Biophoton Light Therapy Mood-Altering Treatments and is by law to be used "FOR EXPERIMENTAL PURPOSES ONLY".

Preliminary Comments:

1. Your BIOPHOTON WAND™ (violet) can radiate a SOLID Violet Light Beam, being powered by the 3 Volt Lithium Battery, which is mounted inside of the Control Box. This SOLID Violet Light Beam may be illuminated experimentally on the following Acupoints: Relax - Shenmen (13), Relax - Zero (19) &/or Addiction/Hunger/Tranquilizer (31)/Anxiety Points (located on left ear), MAJOR Pain (LI-1/No. 2 &/or LI-4/No. 1) Points (located on the right hand), 3rd Eye/7th Chakra/Pineal Gland Point (located just above the center point between the eyebrows on the forehead) &/or CV8/Shenque/Umbilicus/Belly Button Point (located in the center of the solar plexus).
NOTE: The BIOPHOTON WAND™ (red) may work BETTER on the CV8 Point. The CV8 Point is of EXTREME IMPORTANCE, especially in ANY Neurologic Disorder, primarily of Children.

2. Your BIOPHOTON WAND™ (violet) can also radiate a PULSED Violet Light Beam, when a SPECIFIC Frequency/Pulse Rate (i.e. - 2.5 pps. - delta brain wave frequency - sleep & 7.8 pps. - alpha brain wave frequency - balanced awakened state) is being generated by your WAVESHAPER™ Frequency Instrument, while it's in the Square Wave Mode. This PULSED Violet Light Beam can then be shined onto SPECIFIC Points (see Step 1).
NOTE: You won't be ABLE to see the ACTUAL Pulses of the Violet Light Beam with the naked eye, unless you're operating at 50 pps. and below. Also the PULSED Violet Light Beam is about one-half of the Brightness of the SOLID Violet Light Beam, because the WAVESHAPER Frequency Instrument operates at about 50% Duty Cycle in the Square Wave Mode.
Do NOT and I REPEAT, do NOT use the SPECIFIC Frequency/Pulse Rate - 6.6 or the Range of 21-40 for this Biophoton Light Therapy Mood-Altering Treatment Protocol.

3. Please follow these Steps CAREFULLY to ENSURE EFFICIENT Operation of and EFFICACIOUS Results from your BIOPHOTON WAND™ (violet).

4. Operating Steps 1 - 4 can be ELIMINATED, if your BIOPHOTON WAND™ (violet) is being used with your WAVESHAPER™ Frequency Instrument on a REGULAR basis.

Operating Steps:

1. Push the the Red & Black Banana Plugs, which are connected to one end of the 12" Cable, that has a 1/8" Plug connected to the other end, into the matching Red & Black Banana Jacks, which are labeled 'OUTPUT' on the bottom left side of the front panel of your WAVESHAPER™ Frequency Instrument.

2. Push the 1/8" Plug, which is connected to the other end of this 12" Cable, that has Red & Black Banana Plugs now connected to the Red & Black Banana Jacks on your WAVESHAPER™ Frequency Instrument, into the 1/8" Jack, which is labeled 'INPUT', and which is on one end of the Control Box of your BIOPHOTON WAND™ (violet).

3. Push the 1/4" Plug, which is connected to one end of the 12 ft. Coiled-Cable, that has a Black RCA Plug connected to the other end, into the 1/4" Jack, which is labeled 'OUTPUT' on the Control Box.

4. Push the Black RCA Plug, which is connected to other end of the 12 ft. Coiled-Cable, that has the 1/4" Plug now connected to the 1/4" 'OUTPUT' Jack, into the RCA Jack, which is on the Black Cap on the end of your BIOPHOTON WAND™ (violet).

5a. Flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ (violet) to the 'SOLID' Position, if you want to operate BIOPHOTON WAND™ (violet) in the SOLID/CONTINUOUS (sedation) Violet Light Beam Mode.
NOTE: A SOLID Violet Light Beam should NOW be shining from the tip of your BIOPHOTON WAND™ (violet), and if it is, then proceed to Step 6. But if a SOLID Violet Light Beam is NOT shining from the tip of your BIOPHOTON WAND™ (violet), then please check your Cables and Connectors. If they are NOT the PROBLEM, then please call me (Tom) at 614/237-8708 or email me at tharrels@hotmail.com.
Pull the 1/8" Plug out, which is connected into the 1/8" Jack ('INPUT'), on one end of the Control Box, if you want to use your BIOPHOTON WAND™ (violet) in the SOLID/CONTINUOUS Violet Light Beam Mode ONLY. You can then take your BIOPHOTON WAND™ (violet) along with it's Control Box, wherever you want to use your BIOPHOTON WAND™ (violet).

5b. Flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ (violet) to the 'PULSE' Position, if you want to operate your BIOPHOTON WAND™ (violet) in the PULSED (stimulation) Violet Light Beam Mode.

5c. See your WAVESHAPER™ Frequency Instrument - Operating Instructions (IIa - Keypad/Single Frequency Operation).
CAUTION: According to some of the Steps in your WAVESHAPER™ Frequency Instrument - Operating Instructions, you would press CLR (CLEAR), before you press a NEW SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments) into the Keypad or after you've pressed an INCORRECT SPECIFIC Frequency/Pulse Rate into the Keypad. Do NOT, and I REPEAT do NOT press CLR (CLEAR), because 5 Volts will be placed across the HIGH-Intensity Violet LED, which is rated at 3.5 Volts, in your BIOPHOTON WAND™ (violet) and that EXTRA Voltage will SHORTEN it's Life to about 5 minutes!! So if you've pressed a WRONG Number, press ENTER instead, next press the CORRECT number(s) of the SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments) and then press ENTER again. Also, if you want to CHANGE the SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments), press the number(s) of the NEW Frequency/Pulse Rate (see Step 2 - Preliminary Comments) and then press ENTER. After you've pressed the ENTER Button, the previous INCORRECT or CORRECT SPECIFIC Frequency/Pulse Rate will CLEAR and the CORRECT/NEW SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments) will now be displayed and be generated at the 'OUTPUT'.

Lastly, if the CORRECT or NEW SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments), that you want to use, is within 20 Hz., you could use the Tuning Knob (see WAVESHAPER™ Frequency Instrument - Operating Instructions - Ia - TUNING Knob/Single Frequency Operation), thereby ELIMINATING the NEED to press ENTER.

5d. Enter the SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments) into the Keypad.

5e. Turn the Amplitude Control on your WAVESHAPER™ Frequency Instrument CLOCKWISE to it's MAXIMUM setting.
NOTE: A PULSED (SOLID above 50 Hz.) Violet Light Beam should NOW be shining from the tip of your BIOPHOTON WAND™ (violet), and if it is, then proceed to Step 6. But if a PULSED (SOLID above 50 Hz.) Violet Light Beam is NOT shining from the tip of your BIOPHOTON WAND™ (violet), then please check your Cables and Connectors. If they are NOT the PROBLEM, then please call me (Tom) at 614/237-2590 or email me at tharrels@hotmail.com.
The PULSED (SOLID above 50 Hz.) Violet Light Beam is about one-half of the Brightness of the SOLID Violet Light Beam, because the WAVESHAPER™ Frequency Instrument operates at about 50% Duty Cycle in the Square Wave Mode

6. Hold your BIOPHOTON WAND™ (violet) like a Pen and shine it's Violet Light Beam DIRECTLY onto SPECIFIC Points (see Step 1 - Preliminary Comments) at a Distance NOT MORE than 1/4" above or NEXT to the Skin. Move the tip of your BIOPHOTON WAND™ (violet) in a SLOW CLOCKWISE Circle, starting about 1" from the SPECIFIC Point (see Step 1 - Preliminary Comments) and moving towards the center and then holding it in place for 2-5 mins.
NOTE: The tip of your BIOPHOTON WAND™ (violet) can be applied with a GENTLE Pressure onto a SPECIFIC Point (see Step 1 - Preliminary Comments) for 30-90 secs., providing a ROUGH Diagnostic Technique, since the degree of SENSITIVITY of the SPECIFIC Point (see Step 1 - Preliminary Comments) will give a relative evaluation of the status of your Health PROBLEM. You will find that as the Condition of your Health PROBLEM IMPROVES, the SPECIFIC Point SENSITIVITY will be REDUCED!

7. Perform this Procedure on each SPECIFIC Point (see Step 1 - Preliminary Comments), that NEEDS to be treated for 2-5 minutes.
NOTE: This Treatment an be done up to 3 times per day, and each SPECIFIC Point (see Step 1 - Preliminary Comments) should receive a MAXIMUM Treatment Time per Day of 10 mins. (acute conditions) and 15 mins. (chronic conditions).

If you're using MORE than one SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments), then divide the TOTAL Treatment Time of 10 mins. (acute conditions) and 15 mins. (chronic conditions) by the number of SPECIFIC Frequencies/Pulse Rates (see Step 2 - Preliminary Comments) to obtain the amount of Time for each SPECIFIC Frequency/Pulse Rate (see Step 2 - Preliminary Comments).

8a. When you're FINISHED using your BIOPHOTON WAND™ in the SOLID/CONTINUOUS Violet Light Beam Mode, flip the minature Toggle Switch on the Control Box of your BIOPHOTON WAND™ (violet) to the 'PULSE' ('OFF') Position.
NOTE: Eventhough the HIGH-Intensity LED in your BIOPHOTON WAND™ (violet) draws ONLY 20 ma. of Current, you should turn your BIOPHOTON WAND™ "OFF", so that you CONSERVE the 3 Volt Lithium Battery inside of the Control Box.

8b. When you're FINISHED using your BIOPHOTON WAND™ (violet) in the PULSED Violet Light Beam Mode, turn your WAVESHAPER™ Frequency Instrument "OFF".

9. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments until the DESIRED Results are achieved.

Final Comments:

1. DISCONTINUE &/or MODIFY the EXPERIMENTAL Light Treatment with your BIOPHOTON WAND™ (violet), if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (2-3 days), please continue your EXPERIMENTAL Light Treatment.

2. The 3 Volt Lithium Battery will NEED to be replaced, and so you remove the 4 screws in the Top Panel of the Control Box. Desolder the Wires connected to the OLD CR123 Battery and resolder these Wires onto the NEW CR123 Battery, paying CLOSE attention to the Polarity of the Battery.

3. Monitor the duration of the EXPERIMENTAL Biophoton Light Therapy Treatment, using your BIOPHOTON WAND™ (violet) for each Radio Shack No. 63-248).

4. Clean the Lens on the tip of your BIOPHOTON WAND™ (violet) once per week, or as NEEDED, using a Plastic Lens Cleaner (i.e. - Opti-Mist) to ENSURE that the MAXIMUM Output of Violet Light Beam is being emitted.

Revised 5/3/12