MINI-PHOTON LIGHT™ -
Operating Instructions

DISCLAIMER: Your MINI-PHOTON LIGHT™ is to be used "FOR EXPERIMENTAL PURPOSES ONLY".

Preliminary Comments:

1. Your MINI-PHOTON LIGHT™ can radiate a SOLID RED (near-infrared) Light Beam, being powered by 2 - "AA" Alkaline Batteries (3 Volts), which are mounted inside of the Holder/Handle. This SOLID RED Light Beam can then be shined onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point &/or Reflex Point or be used to "light paint" a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).

2. Please follow these Steps CAREFULLY to ENSURE EFFICIENT Operation of and EFFICACIOUS Results from your MINI-PHOTON LIGHT™.

Operating Steps:

1. Insert the 2 - "AA" Alkaline Batteries into the Holder/Handle to turn your MINI-PHOTON LIGHT 8482; "ON", and operate your MINI-PHOTON LIGHT™ in the SOLID/CONTINUOUS (sedation - pain, swelling & inflammation) RED Light Beam Mode.
NOTE: A SOLID RED Light Beam should NOW be shining from the front of your MINI-PHOTON LIGHT™ and if so, then proceed to Step 2a or 2b. But if a SOLID RED Light Beam is NOT shining from the front of your MINI-PHOTON LIGHT™, then please call me (Tom) at 614/237-8708 or email me at tharrels@hotmail.com.

2a. Shine the RED Light Beam DIRECTLY from your MINI-PHOTON LIGHT™ onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point, &/or Reflex Point at a Distance of NO MORE than 1/4" - 1/2" above the Skin and move the RED Light Spot in a SLOW CLOCKWISE Circle, starting about 1" from the Acupuncture Point, Reflex Point or Trigger (center of pain) Point and moving towards the center and then holding the tip in place there for 2-5 mins.

2b. "Light paint" a LARGE (more than 1/4") affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.) by tracing 1" CLOCKWISE Circles with the RED Light Spot at a Distance of NO MORE than 1/2" - 1" above the Skin.
NOTE: The Rate, that you use, when you trace these Circles, can be varied from SLOW to VERY RAPID. CHRONIC Condtions usually respond BEST to a RAPID Rate, whereas ACUTE Condtions usually respond BEST to a SLOWER Rate.
Please see the SPECIFIC Biophoton Light Therapy Treatment Instructions for the Frequency & Duration Of Treatments.

MAJOR PAIN POINTS

MAJOR PAIN POINTS



< No. 2 - A quarter of a finger proximal and towards the thumb from the thumb side of the base of the nail of the index finger.

< No.1 - On the highest point of the hill formed when the straight thumb is pressed against the side of the index finger.

3. Perform this Procedure on each Point/Area, that NEEDS to be treated, for 2-5 minutes.
NOTE: This Procedure can be done up to 3 times per day, and each Point/Area should receive a MAXIMUM Treatment Time per Day of 10 mins. (acute conditions) and 15 mins. (chronic conditions).

4. When you're FINISHED using your MINI-PHOTON LIGHT™ in the SOLID/CONTINUOUS RED Light Beam Mode, please remove 1 - "AA" Battery from the Holder/Handle of your MINI-PHOTON LIGHT ™ to turn it "OFF".
NOTE: Eventhough the HIGH-Intensity LED in your MINI-PHOTON LIGHT™ draws ONLY 30 ma. of Current, you NEED to turn your MINI-PHOTON LIGHT™ OFF" to CONSERVE the 2 - "AA" Batteries, which are inside of the Holder/Handle.

Final Comments:

1. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments with your MINI-PHOTON LIGHT™, until you've obtained the DESIRED Results.

2. DISCONTINUE &/or MODIFY the EXPERIMENTAL Light Treatment with your MINI-PHOTON LIGHT™, if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (1-2 days), please continue your EXPERIMENTAL Light Treatment.

3. Monitor the duration of the EXPERIMENTAL Biophoton Light Therapy Treatments, when you're using your MINI-PHOTON LIGHT™ with a Digital Timer (i.e. - Radio Shack No. 63-878).

4. Clean the Lens on the Red L.E.D. on your MINI-PHOTON LIGHT™ once per week, or as NEEDED, using a Plastic Lens Cleaner (i.e. - Opti-Mist), thus ENSURING that the RED Light Beam is being emitted at it's MAXIMUM Output.

Revised 12/14/04