1) Please remove ALL Metal Ornaments/Jewelry, Watches, Glasses, Pager and Cellphone (and any other devices generating electromagnetic radiations), before doing the following procedure.

2) Please wear Clothes made from NATURAL Fabric(s).

3) Please be SURE that you've read and that you understand your own Frequency Generator - Operating Instructions, before proceeding with Operating Steps 1 - 17.

4) Please preprogram your own Frequency Generator with the REQUIRED Specific Frequencies and Time Periods, if a Programming Function is available, before proceeding with Operating Steps 1 - 17.

5) Please ELIMINATE Operating Steps 1 - 6 (see below), once they are initially COMPLETED, if you're going to use your Hand-Held Plasma Tubes on a REGULAR basis.

6) Please pay SPECIAL attention to the RED NOTE in Step 13 (see below) and the NOTES, which are right after Operating Steps 1, 2, 4, 6 & 12.

7) Please place your Power Supply #1 (black/bone plastic cabinet) within 1 ft. of the rear of your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes, but at LEAST 6 ft. away from your Power Supply #2 (cream-colored metal cabinet) and at least 12 ft. away from your own Frequency Generator.

8) Please place your Power Supply #2 (cream-colored metal cabinet) at LEAST 3 ft. away from your Body, during your EXPERIMENTAL Treatment Session.
NOTE: Your Power Supply #2 (cream-colored metal cabinet) emits a 60 Hz. Electromagnetic Field, which is a Frequency, that can ADVERSELY affect your Health, especially when you're SERIOUSLY ILL.

9) Please place your own Frequency Generator on either a Plastic or a Wood Table and your ELECTRO-CELLULAR ENERGIZER II™ on various shelves of a Book Shelf.
NOTE: Whatever you use, there should be FEW, if ANY, Metal Parts involved.

10) Please clean your BIOENERAY XL3™ Hand-Held Plasma Tubes, if they have Film/Haze on them, with an ammonia-based Glass Cleaner, when they have COOLED DOWN and are NOT being used.

11) Please hold onto the Jack &/or the Plug, rather than holding onto the Cable, when you are connecting or disconnecting Cables, pertaining to the Units, which are involved with your ELECTRO-CELLULAR ENERGIZER II™ & your own Frequency Generator.

12) Please lift your Power Supply #1 (blue/white metal cabinet), when moving it to another location, because sliding your Power Supply #1 (black/bone plastic cabinet) could DISPLACE it's Rubber Feet.

13) Please REPLACE a Metal Amplitude/Intensity Knob, with a Plastic Knob (or wear a glove), if applicable.
NOTE: The High Voltage Electric Field, being generated, can flow from your Body into a Metal Knob and then into your own Frequency Generator, causing Digital Readout PROBLEMS and possible internal DAMAGE!

14) Please do NOT operate your ELECTRO-CELLULAR ENERGIZER II™ CONTINUOUSLY for MORE than 3 hours, because the Power Transistor and Ignition Coils in your Power Supply #1 (black/bone plastic cabinet) could OVERHEAT EXCESSIVELY!
NOTE: If you allow your Power Supply #1 (black/bone plastic cabinet) to COOL DOWN for 15 minutes, you may then use it again CONTINUOUSLY for another 3 hours.

15) Please do NOT operate below 20 Hz. or use the "PULSE" Function (if applicable) below 100 Hz. on your own Frequency Generator.

16a) Please follow Step 16b below, if you're SERIOUSLY-ILL, instead of this Step 16a. Otherwise, please do your EXPERIMENTAL Treatment Session once per day (morning or evening) for a TOTAL EXPERIMENTAL Treatment Time per Session of 10 mins.. Perform your EXPERIMENTAL Treatments for 6 consecutive days, and then NONE on the 7th day. REPEAT the SAME Cycle for 2 MORE weeks and then DISCONTINUE for 1 week. If the DESIRED Results have NOT been achieved, during the 1 week break, then REPEAT your EXPERIMENTAL Treatments, and CONTINUE them until the DESIRED Results are achieved.
NOTE: If you're ABLE, you should INCREASE your TOTAL EXPERIMENTAL Treatment Time on the 2nd Week to 20 mins. and on the 3rd week to 30 mins..

16b) Please do your EXPERIMENTAL Treatment Session, 2 times per day (morning and evening), if you're SERIOUSLY-ILL, starting out with 1-3 mins. per Frequency, and NOT EXCEEDING 10 minutes of TOTAL EXPERIMENTAL Treatment Time each Session. Do your EXPERIMENTAL Treatment Session EVERY 3 days (i.e. - Day Nos. 1, 4, 7, 10, 13, 16, 19 & 22) and then DISCONTINUE for 7 days. If you have NOT achieved the DESIRED Results, during the 1 week BREAK, then REPEAT your EXPERIMENTAL Treatments, and CONTINUE them, until the DESIRED Results are ACHIEVED.
NOTE: If you're ABLE, you should INCREASE your TOTAL EXPERIMENTAL Treatment Time per day on the 2nd Week to 30 mins..

17) Your EXPERIMENTAL Treatment Sessions should ONLY be STOPPED TEMPORARILY, if UNDUE DISCOMFORT is experienced, during the Detoxification Process. If DETOXIFICATION does become TOO UNCOMFORTABLE or ANY ADVERSE Reactions occur, then please DISCONTINUE &/or MODIFY your EXPERIMENTAL Treatment Sessions, and if possible, please try to continue your EXPERIMENTAL Treatment Sessions. Please drink 8 oz. of Activated Charcoal Slurry 6-8 times/day to ADSORB DEAD Pathogens, TOXIC Organic &/or Inorganic Chemicals, that being DETOXED from your Body. Please see Final Comments below) also.

18) Please see Setup Diagram and Setup Diagram 2, before proceeding with Operating Steps 1 - 12.

1) Plug your Power Supply #2 (cream-colored metal cabinet) into a HIGH-Quality Surge Suppressor Power Strip (i.e. - TrippLite - 800+ joules), thus ensuring it's PROTECTION.
NOTE: Your own Frequency Generator (and NO other Electrical/Electronic Device) should also be plugged into this HIGH Quality Surge Suppressor Power Strip. In fact, you should NOT plug ANY other Electrical/Electronic Device into the SAME A.C. Wall Outlet into which this Surge Suppressor Power Strip has been plugged.

2) Push each of the 2 - Brass Ignition Coil Connectors/Adaptors into the High Voltage Towers of each of the Ignition Coils, which protrude through holes in the Rear Panel of your Power Supply #1 (black/bone plastic cabinet), turning each of the 2 - Brass Ignition Coil Connectors/Adaptors clockwise and counterclockwise a few times until each of them are SOLIDLY connected. And then push the Red & Black Banana Plugs connected to each of the ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes into each of the 2 - Brass Ignition Coil Connectors/Adaptors.
NOTE: You MUST SOLIDLY connect the 2 - Ignition Coils in your Power Supply #1 (black/bone plastic cabinet) to your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes, because ARCING, which you may be ABLE to hear, will be generated! ARCING radiates an Interference Signal, which can play HAVOC with and possibly DESTROY Digital Displays and Chips, which are within 3-5 feet of your Power Supply #1 (black/bone plastic cabinet)! And so it would be a GOOD Idea anyhow to keep ANY Devices with Digital Displays and Chips at least 6 ft. away from your Power Supply #1 (blue/white metal cabinet).
You MUST connect your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes to your Power Supply #1 (black/bone plastic cabinet), whenever you're operating them or EXCESSIVE High Voltages will be generated, which will ARC-OVER to Ground, causing Components to BURN-OUT, including the Power Transistor and the 2 - SPECIAL Ignition Coils in your Power Supply #1 (black/bone plastic cabinet)!
You MUST NOT probe around the Ignition Coils or your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes with a Metal Object, such as a Screwdriver, whenever your ELECTRO-CELLULAR ENERGIZER II™ is operating, because you will receive a SEVERE SHOCK and a BURN!!

3) Flip the Toggle Switch to the "A - C" Position, if you want to use the Anti-Parallel Connected Dual-Ignition Coil Circuit to obtain HIGH Electro-Magnetic Fields, which will HELP to DESTROY Pathogens in your Body. Or flip the Toggle Switch to the "S - C" Position, if you want to use the UNIQUE Series-Connected Dual-Ignition Coil Circuit to obtain VERY HIGH Electric (electrostatic) Fields, which will HELP to RAISE Cell Voltages, and which in turn will produce MORE Energy or Detoxification in your Body.
NOTE: DO NOT flip this Toggle Switch, whenever your Power Supply #2 (cream-colored metal cabinet) is "ON", because the Power Transistor can BURN-OUT! Rock the Power Switch to the "OFF" Position FIRST and then after you've flipped the Toggle Switch, you can rock the Power Switch to the "ON" Position again.
When you're using your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes in the "S - C" Mode, you will see that the Plasma Glow is NOT as BRIGHT as it is, when you're operating in the "A - C" Mode. Also, you will feel an INTENSE Electrical Discharge, when using your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes at Frequencies below 200 Hz., so that you may want use the "A - C" Mode ONLY, when you want to operate below 200 Hz..

4) Connect the BNC Plug, which is connected to one end of the 6 ft. Cable #1, which has the 2 - flexible Banana Plugs (or BNC Plug) connected to the other end, to the BNC Jack, which is labeled "PULSE IN", and is mounted on the Front Panel (right side) of your Power Supply #1 (black/bone plastic cabinet).
NOTE: Match the 2 - Slots on the BNC Plug with the 2 - Pins on the BNC Jack and push the BNC Plug 'IN' and then turn the BNC Plug clockwise 1/4 turn.

5) Push the Black Banana Plug, which is connected to the other end of the 6 ft. Cable #1 into the Black Banana Jack, which is on the Front Panel of your own Frequency Generator. Then push the Red Banana Plug into the Red Banana Jack, which is also on the Front Panel of your own Frequency Generator.
Or if there is a BNC Plug connected to the other end of your particular 6 ft. Cable #1, then connect it to the BNC Jack on the Front Panel of your own Frequency Generator.
NOTE: DO NOT plug these Banana Plugs (Red & Black) into the Red & Black Banana Jacks on your Power Supply #2 (cream-colored metal cabinet), because the 12 Volts will BURN-OUT the Power Transistor in your Power Supply #1 (blue/white metal cabinet)!!

6) Push the 2 - stacking-type Gold Banana Plugs (Red & Black) into the corresponding color (Red & Black) Banana Jacks on the Front Panel (left side) of your Power Supply #1 (black/bone plastic cabinet).

7) Flip/Rock/Turn the POWER Switch on your own Frequency Generator to the "ON" Position.

8) Adjust the Amplitude/Intensity on your own Frequency Generator to the setting of '0', if it isn't ALREADY at that particular setting.

9) Program your own Frequency Generator to generate the desired SPECIFIC Frequencies, after reading your Operating Instructions and if applicable, START the Program on your own Frequency Generator.
NOTE: You may also want and/or NEED to use each of the following Frequencies for 3-5 mins.: 64 (oxygen/ozone), 66.5 Hz. (universal pathogen), 528 Hz. followed by 15 Hz. (DNA repair), 727.5 Hz. (universal Rife) and 5,000 Hz. + 10,000 Hz. (cell regeneration).

10) Rock the Power Switch (bottom left side) on your Power Supply #2 (cream-colored metal cabinet) to turn it's Power "ON". Turn the Coarse and/or Fine Voltage Control Knob until the Digital Display reads 15.0 (+/-.2) Volts. Touch and hold the 2 - stacking-type Gold Banana Plugs (Red & Black) together, which haven't yet been connected, and turn the Coarse and/or Fine Current Control Knob until the Digital Display reads 2.0 (+/-.1) Amps. in the S-C Mode (or 3.0 Amps. in the A-P Mode) and then STOP touching these 2 - stacking-type Gold Banana Plugs (Red & Black) together.

11) Push the other 2 - stacking-type Gold Banana Plugs (Red & Black), which are connected to one end of the 6 ft. Cable #2, that has 2 - stacking-type Banana Plugs connected to the other end, into the corresponding color (Red & Black) Banana Jacks, which are labeled "D.C. IN", and are mounted on the Front Panel (bottom left side) of your Power Supply #2 (cream-colored metal cabinet).
NOTE: DO NOT plug these 2 - stacking-type Gold Banana Plugs (Red & Black) into the Red & Black Banana Jacks on your own Frequency Generator, because the 12 Volts will BURN-OUT it's Output Transistors!!
Please observe that the 4" Cooling Fan on the top of your Power Supply #1 (black/bone plastic cabinet) is running and that your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes are NOT yet glowing. If your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes are GLOWING and the Amplitude Control Knob is set at '0' on your own Frequency Generator, then you've got a SHORTED Power Transistor in your Power Supply #1 (black/bone plastic cabinet) and it will NEED to be replaced! Please email and/or call Tom Harrelson (614/237-2590).

12) Turn the Amplitude/Intensity Knob on your own Frequency Generator SLOWLY clockwise from the Setting/Position of '0', until you reach a Setting/Position, where you don't perceptably see a CHANGE in the Brightness of the Plasma Glow when your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes are touching each other, if you turn the Knob SLIGHTLY HIGHER.
NOTE: Whenever you operate your own Frequency Generator at a DIFFERENT Frequency or Frequencies, you may want to CHANGE this Setting/Position SLIGHTLY, and particularly whenever you observe NO or VERY LOW Plasma Glow and especially whenever you're operating in the "S-C" Mode", operating below 100 Hz..
When you've COMPLETED your EXPERIMENTAL Pulsed High Voltage Electrical Field Treatment, then please follow Operating Steps 14 - 17 sequentially and then please see "My Final Comments".

13) Do Lymph Massage, that's similiar to Dry Skin Brushing, using your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes (argon & krypton) like 2 small Brushes to brush or stroke the Skin from the Feet towards the Heart and then from the Head down towards the Heart.
NOTE: You can also hold onto your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes (argon & krypton or helium & neon) like Hand Cylinder Electrodes, having the Red Tube in your Left Hand and the Black Tube in your Right Hand for 5-10 minutes and then having the Black Tube in your Left Hand and the Red Tube in your Right Hand for 5-10 minutes.
Or you can also use an Elastic Bandage to hold each of your ELECTRO-CELLULAR ENERGIZER II™ Hand-Held Plasma Tubes (helium & neon) in place (side-to-side or front-to-back) across an Area (inflammed, swollen, cyst, polyp, tumor, ...), which NEEDS to be treated.

14) Rock the Power Switch on your Power Supply #2 (cream-colored metal cabinet) again to turn the Power "OFF".

15) Turn the Amplitude/Intensity Knob on your own Frequency Generator counter-clockwise to a Setting of 0.

16) Flip/Rock/Turn the Power Switch on your own Frequency Generator to the "OFF" Position.

17) Rock the Power Switch on the Power Strip to turn the Power "OFF" COMPLETELY to your own Frequency Generator and to the Units, which are involved with your ELECTRO-CELLULAR ENERGIZER II™.

1) Drink One 8 oz. glass of PURE Water with a SUPERIOR Probiotic Product daily to replenish your FRIENDLY Intestinal Bacteria.
NOTE: This Probiotic Product is AVAILABLE from Health Food Stores or an Online Websites.

2) Drink 6-8 Glasses of Activated Charcoal Slurry (1 tsp./8 oz. - pure water) daily to ADSORB the HIGHER-than-normal amounts of TOXINS, which are NOW in your Bloodstream.
NOTE: Activated Charcoal Powder is AVAILABLE from Tom Harrelson/TOTAL HEALTH Associates/774-D S. Chesterfield Rd./Columbus, OH 43209-2683/614-237-2590.

3) Take a SUPERIOR Laxative & Colon Cleanser (i.e. - Dr. Schulze's Intestinal Formulas #1 & #2) daily also (use as directed) to move the Bowels and ADSORB the TOXINS from the Intestines.
NOTE: Dr. Schulze's Intestinal Formulas #1 & #2 are AVAILABLE from American Botanical Pharmacy/800-437-2362.