By law, I must tell you that at NO time should the PHOTON TORCH 2™ be used to replace PROPER Medical Treatment, or be considered as a Replacement for PROPER Physician Care and for ALL Medical Conditions consult your Physician FIRST, before using this Experimental Biophoton Device, unless, of course, you are a physician.

1. Your PHOTON TORCH 2™ radiates a SOLID/CONTINUOUS or PULSE 660 nm Deep Red Light Beam, being powered by 3 - 1.5 Volt AA Batteries, which are contained inside it's Case. This SOLID/CONTINUOUS or PULSE 660 nm Deep Red Light Beam can then be shined onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point &/or Reflex Point or be used to "light paint" a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).

2. Please follow these Steps CAREFULLY to ENSURE EFFICIENT Operation of and EFFICACIOUS Results from your PHOTON TORCH 2™.

1. Push the Black Button ONCE on the front of the Handle of your PHOTON TORCH 2™ and it will turn "ON" the 660 nm Deep Red Light Beam in the SOLID/CONTINUOUS - HI mode.
NOTE: Pushing the Black Button a 2nd time will turn "ON" the 660 nm Deep Red Light Beam in the SOLID/CONTINUOUS - LO mode. Pushing the Black Button a 3rd time will turn "ON" the 660 nm Deep Red Light Beam in the PULSE - HI mode. Use the PULSE - HI mode, if you have a chronic condition and/or have built-up a tolerance to using the SOLID/CONTINUOUS - HIGH or LO modes, and if you've NOT been obtaining the desired healing results.

2a. If a SMALL involved area, such as a Acupuncture Point, Trigger Point &/or Reflex Point, needs to be treated, then CAREFULLY pull the head forward, while SLOWLY turning the head clockwise. Next, shine the smaller Light Spot on this SMALLER involved area. Also, push the black button until you see the LO Light Beam, when you want to shine the 660 nm Deep Red Light Beam DIRECTLY onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point, &/or Reflex Point at a Distance of about 1/4" above the Skin, starting about 1" from the Acupuncture Point, Reflex Point &/or Trigger (center of pain) Point, moving towards the center and lastly holding the Head close this Point for 1-3 mins..

2b. When treating a LARGE involved area, push the black button until you see the HI Light Beam. Then "light paint" the LARGE (more than 1/2") affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.) by tracing 1" CLOCKWISE Circles with the 660 nm Deep Red Light Beam. Continue to "light paint" the LARGE Area for 3-5 mins..
NOTE: The Rate, that you use, when you trace these Circles, can be varied from SLOW to VERY RAPID. CHRONIC Condtions usually respond BEST to a RAPID Rate, whereas ACUTE Condtions usually respond BEST to a SLOWER Rate. If the DESIRED healing results are NOT obtained, then push the black button until you see the PULSED Light Beam and use this Light Beam Mode for the SAME amount of time to obtain the DESIRED healing results.
Please see the SPECIFIC Biophoton Light Therapy Treatment Instructions for the Frequency & Duration Of Treatments.

3. Perform this Procedure on each Point/Area, that NEEDS to be treated, for 1-3 minutes.
NOTE: This Procedure can be done up to 3 times per day, and each Point/Area should receive a MAXIMUM Treatment Time per Day of 3 mins. (acute conditions) and 5 mins. (chronic conditions).

4. When you're FINISHED using your PHOTON TORCH 2™ in the SOLID/CONTINUOUS 660 nm Deep Red Light Beam Mode, push the Black Button on the handle of your PHOTON TORCH 2™ until you turn the 660 nm Deep Red Light Beam "OFF".
NOTE: The 7 Watt Luxeon LED in your PHOTON TORCH 2™ draws about 1500 ma. of Current, and so you NEED to turn the Light Beam "OFF" to CONSERVE the Energy of the 3 - 1.5 Volt AA Batteries, which are inside it's Case.

1. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments until you've obtained the DESIRED Results.

2. DISCONTINUE &/or MODIFY the EXPERIMENTAL Light Treatment with your PHOTON TORCH 2™, if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (1-2 days), please continue your EXPERIMENTAL Light Treatment.

3. Monitor the duration of the EXPERIMENTAL Biophoton Light Therapy Treatments, when you're using your PHOTON TORCH 2™ with a Digital Timer (i.e. - Radio Shack No. 63-878).

4. Clean the Lens on the Head of your PHOTON TORCH 2™ once per week, or as NEEDED, using a 3M Lens Cleaning Cloth, thus ENSURING that the 660 nm Deep Red Light Beam is being emitted at it's MAXIMUM Output.

5. Do NOT look DIRECTLY into or view DIRECTLY with Optical Instruments the Light Beam from your PHOTON TORCH 2™ for MORE than 1-2 seconds, thus ENSURING that there will NOT be a Spot before your Eyes for 1 or MORE Hours!
CAUTION: If your PHOTON TORCH 2™ contains an Infrared LED (special order), then you must NOT look directly into the lens for any length of time!

7. Do NOT allow a Child to operate your PHOTON TORCH 2™, unless he/she is SUPERVISED by an Adult!