By law, I must tell you that at NO time should the PHOTON TORCH™ be used to replace PROPER Medical Treatment, or be considered as a Replacement for PROPER Physician Care and for ALL Medical Conditions consult your Physician FIRST, before using this Experimental Biophoton Device, unless, of course, you are a physician.

1. Your PHOTON TORCH™ radiates a SOLID (0 pps - chronic pain) or PULSE (8.5 pps - acute pain) Deep Red (near-infrared - 660 nm) or another color Light Beam, being powered by 2 - 'AA' Alkaline Batteries, which are contained inside it's Case/Handle. This SOLID or PULSE Deep Red (near-infrared - 660 nm) or another color Light Beam can then be shined onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point &/or Reflex Point or be used to "light paint" a LARGE affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.).
NOTE: The Light Beam of your PHOTON TORCH™ can be adjusted from flood-to-spot by pulling the head forward and vice-versa.

2. Please follow these Steps CAREFULLY to ENSURE EFFICIENT Operation of and EFFICACIOUS Results from your PHOTON TORCH™.

1. Softly push the Black Rubber Button on the end of the Case/Handle of your PHOTON TORCH™ to turn "ON" Deep Red (near-infrared - 660 nm) or another color Light Beam in the SOLID - HI mode.
NOTE: Softly pushing the Black Rubber Button again to turn "ON" the Deep Red (near-infrared - 660 nm) or another color Light Beam in the SOLID - LO mode. Softly pushing the Black Rubber Button a 3rd time will turn "ON" the Deep Red (near-infrared - 660 nm) or another color Light Beam in the HI PULSE (8.5 pps) mode.

2a. When treating a SMALL area, such as a Acupuncture Point, pull the Head forward, until it STOPS, to project a SMALL Spot Light Beam. Also, softly push the end cap button to see the LO Light Beam. Hold your PHOTON TORCH™ like a Pen, gripping around the Case/Handle near the Head, when you want to shine the Deep Red (near-infrared - 660 nm) or another color Light Beam DIRECTLY onto a SPECIFIC Acupuncture Point, Trigger (center of pain) Point, &/or Reflex Point at a Distance of 1/2 to 1" above the Skin or, BETTER yet, place the end of the tip of of your PHOTON TORCH™ NEXT to the Skin and move the Head in a SLOW CLOCKWISE Circle, starting about 1" from the Acupuncture Point, Reflex Point or Trigger (center of pain) Point, moving towards the center and lastly holding the Head on this Point for 1-3 mins..
NOTE: If your Hand/Wrist gets TIRED, holding your PHOTON TORCH™ in the "Pen" Position, curl your Fingers around the Case/Handle, while it's resting on the Base of the palm of your Hand underneath. If your Hand is MORE COMFORTABLE in this NEW Handhold Position, you may want to use it indefinitely, instead of using the "Pen" Position.

2b. When treating a LARGE area, pull the Head backward, until it STOPS, to project a WIDE Light Beam. Also, softly push the end cap button until you see the HI Light Beam. Then "light paint" the LARGE (more than 1/2") affected Body Area (i.e. - Skin, Joints, Involved Muscles, Tumors, etc.) by tracing 1" CLOCKWISE Circles with the Deep Red (near-infrared - 660 nm) or another color Light Beam. Continue to "light paint" the LARGE Area for 3-5 mins. at a distance of 1/2 to 1 inch away.
NOTE: The Rate, that you use, when you trace these Circles, can be varied from SLOW to VERY RAPID. CHRONIC Condtions usually respond BEST to a RAPID Rate, whereas ACUTE Condtions usually respond BEST to a SLOWER Rate. If the DESIRED healing results are NOT obtained, then softly push the end cap button until you see the PULSED (8.5 pps) Light Beam and use this Light Beam Mode for the SAME amount of time to obtain the DESIRED healing results.
Please see the SPECIFIC Biophoton Light Therapy Treatment Instructions for the Frequency & Duration Of Treatments.

3. Perform this Procedure on each Point/Area, that NEEDS to be treated, for 1-3 minutes.
NOTE: This Procedure can be done up to 3 times per day, and each Point/Area should receive a MAXIMUM Treatment Time per Day of 3 mins. (acute conditions) and 5 mins. (chronic conditions).

4. When you're FINISHED using your PHOTON TORCH™ in the SOLID Deep Red (near-infrared - 660 nm) or another color Light Beam Mode, push the Black Rubber Button FIRMLY on the end of the Case/Handle of your PHOTON TORCH™ until the Deep Red (near-infrared - 660 nm) or another color Light Beam turns "OFF", then you RELEASE the pressure on the Black Rubber Button.
NOTE: The 3 Watt Luxeon LED in your PHOTON TORCH™ draws 700 ma. of Current, and so you NEED to turn the Light Beam "OFF" to CONSERVE the Energy of the 2 - 'AA' Alkaline Batteries, which are inside it's Case/Handle.

1. Continue your EXPERIMENTAL Biophoton Light Therapy Treatments until you've obtained the DESIRED Results.

2. DISCONTINUE &/or MODIFY the EXPERIMENTAL Light Treatment with your PHOTON TORCH™, if DETOXIFICATION becomes TOO UNCOMFORTABLE, but then just as SOON as possible (1-2 days), please continue your EXPERIMENTAL Light Treatment.

3. Monitor the duration of the EXPERIMENTAL Biophoton Light Therapy Treatments, when you're using your PHOTON TORCH™ with a Digital Timer (i.e. - Radio Shack No. 63-878).

4. Clean the Lens on the Head of your PHOTON TORCH™ once per week, or as NEEDED, using a 3M Lens Cleaning Cloth, thus ENSURING that the Deep Red (near-infrared - 660 nm) or another color Light Beam is being emitted at it's MAXIMUM Output.

5a. Please REMOVE the end cap and the EXPIRED original 'AA' Alkaline Batteries.

5b. Insert the POSITIVE end FIRST, observing the CORRECT Polarity with either 2 - 'AA' Alkaline, 'AA' Lithium-Ion, 'AA' Nickel-Cadium or 'AA' Nickel Metal Hydride Batteries. Please do NOT MIX types of batteries. You can use rechargeable or nonrechargeable batteries.

6. Do NOT look DIRECTLY into or view DIRECTLY with Optical Instruments the Light Beam from your PHOTON TORCH™ for MORE than 1-2 seconds, thus ENSURING that there will NOT be a Spot before your Eyes for 1 or MORE Hours!

7. Do NOT allow a Child to operate your PHOTON TORCH™, unless he/she is SUPERVISED by an Adult!