RUNNING A PREPROGRAM
Choose a disease condition from the Frequency and Procedural Manual, and note the program number on the left hand margin. This is the number you will be entering to run a program.
1. Press Power On/Off (all buttons indicated by Bold)
2. Wait for messages to scroll across screen—10 seconds (all messages on screen indicated by all CAPITAL LETTERS and BOLD)
3. You will see, P.P. 1 A.L.S.
4. Press Next
5. You will see, P.P. and a blinking 1
6. Press Change +
7. You will see P.P. and a blinking 2 
8. Press Change + repeatedly until the first digit on the screen matches the first digit from the program you have chosen.
9. Press Next
10. You will see the first digit from your chosen program, and a blinking O
11. Press Change + repeatedly until the second digit on the screen matches the second digit from the program you have chosen.
12. Press Next
13. You will see the first two digits from your chosen program and a blinking O
14. Press Change + repeatedly till the third digit on the screen matches the third digit from the program you have chosen.
15. If you have made an error and added more digits on the screen than in your program selection, press Change + until the extra digit is zero, then press Back.
16. If needed, repeat steps #12 and #14 until all the digits on the screen match all the digits from the program you have chosen.
17. Press OK/.
18. You will see the name of the program you have chosen and SEQ-YES
19. Press OK/.
20. You will see USE DEFAULTS—NO
21. Press Change +
22. You will see USE DEFAULTS—YES (It is much easier to learn how to run programs using USE DEFAULTS—YES. In this mode, the BCX Ultra will make several choices for you such as the time each frequency runs, the wave form, intensity, etc. In the next section, you will learn in detail about the defaults, the options you have and how to make changes in the program).
23. Press OK/.
24. You will see ELECT. + RAY TUBES
25. Press OK/.
26. You will see PLUG ELECT. + TUBES
27. Plug in the wires of the Ray tubes and electrodes in the corresponding outlets.
28. Press OK/.
29. You will see PRESS START NOW
30. Press Start/Pause
31. You will see starting in >5, >4, >3, >2, >1, on the screen. The program is now running.
32. You can change electrode intensity anytime while the program is running by pressing Change + to increase, or Change – to decrease.
33. You can change ray tube intensity anytime while the program is running by pressing Next to increase or Back to decrease.
34. Wait until you see PROGRAM ENDED
OPTIONS:
Press Start/Pause at any time to pause program
Press Start/Pause again to resume program
Press Stop at any time to stop the program before it is finished
DEFAULTS:
Do not get overwhelmed by the Default section. Many of the selections within the Default mode are used primarily by doctors and scientists for experimentation. Under certain circumstances the average person may only need to change a few of the options. Other times, no changes will be necessary and choosing DEFAULTS—YES as previously demonstrated, allows you bypass these options since the BCX has preprogrammed the standard choices. Each of the 14 default options will be explained briefly. For a more thorough description, see the enclosed literature.
DEFAULTS—DETAILED INSTRUCTIONS:
Repeat steps 1-20 from RUNNING A PROGRAM on page one of BCX Ultra Operating Instructions. You will see USE DEFAULTS—NO on the screen, and then press OK/.
A. You will see ELECT+RAYTUBES
The choices are: ELECT. + L.E.D. WAND, ELECT + EXTERNAL (External refers to an accessory that is in the process of being developed. It is not available at this time.), OUTPUT=ELECTRODE, OUTPUT=RAY TUBES, OUTPUT=LED WAND, OUTPUT=EXTERNAL WAND 
Press Change + repeatedly until the desired accessories are on the screen, then press OK/.
B. You will see RUN MINUTES= 3
The choices are 1 to 120 minutes. This means that each frequency will run for 3 minutes.
Press Change + or Change - until desired run time is on the screen, then press OK
C. You will see DUTY CYCLE= 90. 
Choices are 1 to 100. Duty cycle is how long the frequency is on and off per second. The 80% duty cycle, which is standard, exposes the microorganism for 80% of each second then is off for 20% of each second. It is known that the higher the duty cycle, the greater the coordinated resonance.
Press Change+ repeatedly until desired duty cycle is on the screen then press OK/.
D. You will see GATE — SQUARE
These are the wave forms. There are 16 types of waveforms. Square is for killing pathogens. Sine is for healing and regeneration. The remaining 14 waveforms are not used as frequently.
Press Change + repeatedly until desired waveform is on the screen, then press OK/.
E. You will see GATE Hz. = 3.5 
The choices are from 1 to 100,00 Hz. Royal Rife used 3.5-4 Hz for gating. For a detailed explanation on gating, see the enclosed literature.
Press Change + repeatedly until desired Hz is on the screen, then press OK/.
F. You will see ELECT. INT.= 40
The choices are from 1 to 100. The intensity of the electrodes can also be adjusted anytime while the program is running.
Press Change + or Change - repeatedly until desired intensity is on the screen, then press OK/.
G. You will see RAYTUBE INT.= 80
The choices are 1 to 100. The intensity of the ray tubes can also be adjusted anytime while the program is running.
Press Change + or Change - until desired intensity is on the screen, then press OK/.
H. You will see SOFT START—YES
Choices are YES or NO. When you choose Yes, the BCX slowly brings the intensity up to the desired setting over a period of approximately 5 seconds.
Press Change + until desired soft start is displayed, then press OK/.
I. You will see AUTOSHUT OFF—YES
The machine shuts down automatically after the program is finished. The choices are Yes or No.
Press Change + until desired autoshut off is displayed, then press OK/.
J. You will see CARRIER—YES
Your choices are yes or no. When you choose yes, a Radio Frequency carrier assists the frequencies to penetrate into the cells of the body.
Press Change + until desired option is displayed, then press OK/.
K. You will see C. WAVE—SQUARE
There are 16 waveforms to choose from. Square is for killing pathogens. Sine is for healing and regeneration. The remaining 14 waveforms are not used as frequently.
Press Change + until desired waveform is displayed, then press OK/.
L. You will see F. WAVE—SQUARE 
There are 16 waveforms to choose from. Square is for killing pathogens. Sine is for healing and regeneration. The remaining 14 waveforms are not used as frequently.
Press Change + until desired waveform is displayed, then press OK/.
M. You will see CARRIER 1=1.00 MHz.
The choices are 1 to 100,000 Hz. 1.25 MHz, 1.67 MHz. Scientific studies have shown that the closer a carrier wave gets to 1 megahertz the greater the penetration into the cell.
Press Change + or Change - until you see the level of Hz you want on the screen, and then press OK/.
N. You will see 1= **** (the frequency displayed will be the first frequency on the list from the program you are running). Press OK/.
O. Press OK/. repeatedly as the BCX scrolls through the list of frequencies from the program you have selected.
P. You will see MORE FREQ. ---NO
Your choices are YES or NO. If you choose NO, skip to step m) below as you will not run any additional frequencies other than the ones in the program you have selected. If you choose YES, proceed through all the steps below as this option allows you to run frequencies in addition to the ones listed in the program you have selected. 
Press Change + until you see YES or NO on the screen, and then press OK/.
a) You will see FREQ. ?, (indicating the next consecutive number following the list of frequencies in your chosen program) =1
b) Press Change + repeatedly until the first digit on the screen matches the first digit in the frequency you want to add.
c) Press Next
d) You will see the first digit from your selected frequency and a blinking 0 on the screen.
e) Repeat steps b) and c) above until all the digits on the screen match all the digits from the frequency you want to add.
f) If you have made an error, press Change + until the unwanted digit is a 0, then press Back
g) When all digits are correct press Ok/.
h) You will see the frequency you have selected with a decimal point at the end.
i) Press Ok/. again.
j) You will see MORE FREQ.—YES 
k) Press OK/.
l) After you have entered all the additional frequencies you have selected by following steps a)—j) above, you will see MORE FREQ.—YES.
m) Press Change +
n) You will see MORE FREQ.—NO 
o) Press OK/.
p) You will see PLUG ELECT.+ TUBES
q) Plug in the corresponding wires
r) Press OK/.
s) You will see PRESS START NOW on the screen
t) Press Start/Pause

BCX ULTRA
ENTERING MANUAL PROGRAMMING
Manual programming allows you to design your own custom list of frequencies to create your own program. You will enter each frequency, name the program and save it for future use. The last section will show you how to find the manual programs you have created. To begin, look through the Frequency and Procedural Manual and compile a list of frequencies for your custom program.
1. Press Power On/Off (all buttons indicated by Bold)
2. Wait until messages scroll across screen (about 10 seconds) (all messages displayed on screen indicated by all CAPITAL LETTERS and BOLD)
3. You will see P.P. 1 A.L.S. 
4. Press Change –
5. You will see PROGRAM MANUALLY
6. Press OK/.
7. You will see M.P. 1 (Manual Program) EMPTY
8. Press OK/.
9. You sell see ELECT. + RAY TUBES
10. Press OK/.
11. You will see RUN MINUTES= 3
12. Press OK/.
13. You will see DUTY CYCLE= 90
14. Press OK/.
15. You will see GATE – SQUARE 
16. Press OK/.
17. You will see GATE Hz.= 3.5
18. Press OK/.
19. You will see ELECT. INT.= 40
20. Press OK/.
21. You will see RAYTUBE INT. = 80
22. Press OK/.
23. You will see SOFT START—YES
24. Press OK/.
25. You will see AUTO SHUTOFF—YES
26. Press OK/.
27. You will see CARRIER—YES
28. Press OK/.
29. You will see C. WAVE—SQUARE
30. Press OK/.
31. You will see F.WAVE—SQUARE
32. Press OK/.
33. You will see CARR.1 = 1.00 MHz.
34. Press OK/.
35. You will see FREQ.1 = 1 
36. Press Change + repeatedly until the 1st digit on the screen matches the 1st digit of the frequency you want to run (you will now be entering your first frequency from the list you have compiled)
37. Press Next
38. Press Change + repeatedly until the 2nd digit on the screen matches the 2nd digit of the frequency you want to run
39. Press Next
40. Press Change + repeatedly until the 3rd digit on the screen matches the 3rd digit of the frequency you want to run
41. If you have made an error and have added more digits on the screen than in your frequency, press Change + until the extra digit is zero, then press Back.
42. When you have finished entering all the digits of the frequency you want to run, press OK/.
43. You will see FREQ.1 = **** (your frequency # here) followed by a decimal point
44. Press OK/.
45. You will see MORE FREQ.—NO
46. Press Change + for MORE FREQ.—YES to add another frequency 
47. Press OK/.
48. You will see FREQ. 2 = 1
49. Press Change + repeatedly until the 1st digit on the screen matches the 1st digit of the frequency you want to enter
50. Press Next
51. Press Change + repeatedly until the 2nd digit on the screen matches the 2nd digit of the frequency you want to run
52. If you have made an error and you see an extra digit on the screen, press Change + repeatedly until the extra digit is a zero, then Press Back
53. Press OK/. to insert a decimal point if needed. When you insert a decimal point, you will need to fill up the remainder of the screen with zeros by pressing Next repeatedly. This keeps the decimal in place. (If you insert a decimal, you will not see the next three steps appear on the BCX Ultra, and you will skip to step # 57)
54. When the digits on the screen match the digits from the frequency you want to enter, Press OK/.
55. You will see FREQ 2 = **** (your frequency # here) followed by a decimal point
56. Press OK/. again 
57. You will see MORE FREQ. = YES
58. Repeat steps 45—54 above until all frequencies are entered
59. You will see MORE FREQ.—YES
60. Press Change +
61. You will see MORE FREQ.—NO
62. Press OK/.
63. You will see SAVE PROGRAM—YES
64. Press OK/.
65. You will see M.P. 1 and a blinking cursor 
66. Press Change + repeatedly until the 1st letter on the screen matches the 1st letter for the name of the program. (Here you will create a name for this custom program such as flu, allergy, etc.)
67. Press Next
68. Press Change + repeatedly until the 2nd letter on the screen matches the 2nd letter for the name of the program.
69. Press Next for more letters, repeat steps 69 and 70 for additional letters then press OK/. when you have finished entering a name.
70. You will see RUN PROGRAM—YES
71. Press OK/.
72. You will see PLUG ELECT. + TUBES
73. Plug in corresponding wires for the electrodes and ray tubes in the correct outlets
74. Press OK/.
75. You will see PRESS START NOW
76. Press Start/Pause
77. Program will run

RUNNING A MANUAL PROGRAM
In this section, you will retrieve and run a manual program you have created previously.
1) Press Power On/Off
2) Wait for messages to scroll across screen (10 seconds)
3) You will see P.P. 1 A.L.S.
4) Press Change -
5) You will see PROGRAM MANUALLY
6) Press OK/.
7) You will see M.P. 1 and the name of the program
8) Press Change + repeatedly until the name of the Manual Program you want to run is displayed on the screen
9) Press OK/.
10) You will see ELECT. + RAY TUBES
11) Press OK/.
12) You will see RUN MINUTES= 3
13) Press OK/.
14) You will see DUTY CYCLE= 90
15) Press OK/.
16) You will see GATE – SQUARE 
17) Press OK/.
18) You will see GATE Hz.= 3.5
19) Press OK/.
20) You will see ELECT. INT.= 40
21) Press OK/.
22) You will see RAYTUBE INT.= 80
23) Press OK/.
24) You will see SOFTSTART—YES 
25) Press OK/.
26) You will see AUTOSHUTOFF—YES
27) Press OK/.
28) You will see CARRIER—YES
29) Press OK/.
30) You will see C. WAVE—SQUARE
31) Press OK/.
32) You will see F. WAVE—SQUARE
33) Press OK/.
34) You will see CARR. 1 = 1.00 MHz.
35) Press OK/.
36) You will see FREQ. 1 = **** (The first frequency from your custom program will be displayed here)
37) Press OK/.
38) You will see FREQ. 2= **** (the 2nd frequency from your custom program will be displayed here)
39) Press OK/.
40) Press OK/. repeatedly as the BCX scrolls through the list of frequencies. When you have scrolled through the list…
41) You will see MORE FREQ.—NO
42) Press OK/.
43) You will see SAVE PROGRAM—YES 
44) Press OK/.
45) You will see M.P.—and the name of your custom program with a blinking cursor
46) Press OK/.
47) You will see RUN PROGRAN—YES
48) Press OK/.
49) You will see PLUG ELECT. + TUBES
50) Plug in wires in the corresponding outlets
51) Press OK/.
52) You will see PRESS START NOW
53) Press Start/Pause
54) Program is running