HOME PAGE PRICE LIST HEALING TOOLS ORDER FORM|
HOME PAGE |
PRICE LIST |
HEALING TOOLS |
ORDER FORM |
| MAIN PAGE |
ACTIONS |
CIRCUIT DESIGN |
RESEARCH |
|
TECHNOLOGY Revised 12/12/12
My 1st Generation Plasma Tube Unit - the BIOENERAY TUBE™ was built and tested about 5 years ago and my 2nd Generation Plasma Tube Unit - the BIOENERAY TUBE XL™ was built and tested about 1 year later, using Jimmie Holman's Poor Man's Rife Plasma Tube Driver Circuit in the High Voltage Power Supply for BOTH Plasma Tube Units. I had installed a Standard Automotive Ignition Coil and tested the Output of the Electro-Magnetic Field. I then installed a SPECIAL High Performance Automotive Ignition Coil, which has an ISOLATED Primary and Secondary, unlike a Standard Automotive Ignition Coil, which has a COMMON Ground, and a HIGHER (1 1/2 times) Electro-Magnetic Field was generated, than had been generated, using a Standard Automotive Ignition Coil! In my 3rd Generation BIOENERAY XL2™ & XL3™ Plasma Tube Units, I originally installed and connected 2 - 6 Volt Motorcycle Ignition Coils (higher R.P.M. & 1.5 ohm D.C. primary resistance) in a Parallel Connected Circuit and a HIGHER (2-3 times) Electromagnetic Field was generated, than had been generated, using the single SPECIAL High Performance Automotive Ignition Coil! Afterwards, I connected these 2 - 6 Volt Motorcycle Ignition Coils in a non-standard Anti-Parallel Connected Circuit and an even HIGHER (1 1/2 times) Electro-Magnetic Field was generated, than had been generated, using the 2 - 6 Volt Motorcycle Ignition Coils in the standard Parallel Connected Circuit! After I had COMPLETED these Electromagnetic Field Output Tests, I was INSPIRED to connect these SAME 2 - 6 Volt Motorcycle Ignition Coils in my own UNIQUE Series-Connected Circuit. A MUCH HIGHER (3-5 times) Electro-Static Field, as opposed to a HIGHER Electro-Magnetic Field, was generated!! My NEW and IMPROVED 4th Generation Plasma Tube Unit - ELECTRO-CELLULAR ENERGIZER II™ was built and tested, using Jimmie Holman's Poor Man's Rife Plasma Tube Driver Circuit again in the NEWEST ELECTRO-CELLULAR ENERGIZER II™ High Voltage Power Supply. Your Frequency Instrument generates LOW Voltage Square Wave Pulses at a SPECIFIC LOW (audio) Frequency
into the Input of the High Voltage Power Supply, which is powered by the TENMA 0-40 Volts/0-5 Amps. D.C. Power Supply. The Custom-Built High-Voltage Power Supply then generates a Pulsed High Voltage from 2 - 6 Volt Automotive Ignition Coils connected in my own UNIQUE Series-Connected Circuit, that next ionizes the Mercury Vapor and afterwards the Gasses inside of the Glass Plasma Tube into a Plasma State. The Glass Plasma Tube lastly radiates a HIGH Pulsed Electro-Static Field towards, through and beyond your Body. NOTE: The "E" Gas + Mercury Vapor Plasma Tube is custom-made by Barry Allred, and is made using Leaded Glass, thus resulting in neither Ultra-Violet nor X-Rays being emitted!! Various Gas Mixtures and Pressures have been tested during 2 Years of INTENSIVE Laboratory Research, so that you can be ASSURED that my ELECTRO-CELLULAR ENERGIZER II™ (clinical unit) will deliver OPTIMAL Results!
1 - 0-40 Volts/0-5 Amps. D.C. Power Supply, 1 - 6 ft. Dual-Conductor D.C. Power Cable (& 4 - Gold-Plated Stacking-Type Banana Plugs), 1 - 6 ft. Y-Cable (& 2 - Flexible Banana Plugs + 1 - BNC Plug) or 1 - 6 ft. Cable (& 2 - BNC Plugs), 1 - High Voltage Power Supply [1 - Plastic Cabinet - 3" H. X 8" W. X 11" D., 2 Heavy Duty Banana Jacks (red & black), 2 - Banana Jacks (red & black), 1 - BNC Jack, 1 - 330 ohm 1/2 watt Resistor, 1 - NPN Power Transistor (MJ11016 or BUX48A), 1 - DPDT Switch, 1 - 50 mm Fan, 1 - 50 mm Fan Guard, & 2 - 6 Volt Automotive Ignition Coils] and 1 - Plasma Tube Setup (2 - 3 ft. SUPER-Flexible HIGH Voltage Wires & 2 - Heavy-Duty Banana Plugs, 1 - Custom-Made Wood Stand/Holder (5" H. X 22" W. X 5 1/2" D.) & 1 - Custom-Made Straight Glass Plasma Tube (14" L. X 4" dia. bubble - "E" Gas + Mercury Vapor).
|
