BIOMAGNESONIC TRANSDUCER II™ +
WAVESHAPER™ Frequency Instrument -
Operating Instructions

DISCLAIMER: TOTAL HEALTH ASSOCIATES makes NO SPECIFIC Medical Claims for the BIOMAGNESONIC TRANSDUCER II™, and does NOT dispense Medical Advice. The BIOMAGNESONIC TRANSDUCER II™ is NOT registered as a Medical Device with the U.S. Food and Drug Administration and is to be used "FOR EXPERIMENTAL USE ONLY". Please consult your Physician regarding ANY undiagnosed Condition or before ENHANCING your Treatment with this EXPERIMENTAL Biomagnetic, Electromagnetic, Sonic & Pressure Wave Therapy.

CAUTION - The BIOMAGNESONIC TRANSDUCER II™ should never be used with a Frequency LOWER than 5 Hz., while driving a Vehicle to AVOID the DANGER of falling ASLEEP at the Wheel.
The BIOMAGNESONIC TRANSDUCER II™ can produce Sound Frequencies, which tend to dissolve Blood Clots. Therefore, this Unit should NOT be used in the following circumstances:
(1) on anyone, who has a Phlebitis.
(2) on anyone, who has Thrombosis, especially using 10 Hz..
(3) on anyone, who has NOT had several weeks of GOOD Healing after Major or Minor Surgery.
(4) on anyone, who has suffered a Stroke, which was caused by an Artery rupturing in the Brain.

or in the following circumstances:
(1) on anyone, who is Pregnant or is suspected of being Pregnant.
(2) on anyone, who has Epilepsy &/or Convulsions.
(3) on anyone, who has a Psychotic Disorder.
(4) on anyone, who has Glaucoma.
(5) on anyone, who has Back Problems.
(6) on anyone, who has Hypertension with resistance to Medical Therapy.
(7) on anyone, who has Heart Problems, especially using 1 Hz..
(8) on anyone, who wears a Pacemaker &/or a Defibrillator, especially using 1 Hz..
(9) on anyone near skeletal degenerative disorders.
(10)on anyone on the stomach region at 7 Hz..

Preliminary Comments

1) Before starting this EXPERIMENTAL Treatment, please be SURE that you've read and understand the WAVESHAPER™ Frequency Instrument - Operating Instructions, plus NOTE, DISCLAIMER and CAUTION in the Box at the bottom of this Page.

2) Please ELIMINATE Steps 1 - 5 in the following Operating Steps, once they are COMPLETED the FIRST Time, if you're using your BIOMAGNESONIC TRANSDUCER II™ on a regular basis.

3) Please push the Slide Switches into the NORMAL and MUSIC Positions and the turn the 'FILTER' Knob at the MAXIMUM Setting of 10 on your Infratonic Amplifier, if you want to obtain OPTIMAL Results.

4) Perform the following Procedure 2-3 times per day for a TOTAL Experimental Treatment Time per Session of 15/20 mins..
NOTE: INCREASE your TOTAL Experimental Treatment Time on the 2nd Week to 20 mins. (Acute) & 25 mins. (Chronic), on the 3rd week to 25/30 mins. and on the 4th week to 30/35 mins..

5) Perform your Experimental Treatments 1 - 2 times daily (morning &/or evening - total time - 1 hr.) for 6 consecutive days, then NONE on the 7th day, REPEATING the SAME Cycle for 2 MORE weeks and then DISCONTINUE for 1 week. If the DESIRED Results have NOT been achieved, then REPEAT your Experimental Treatments after the 1 week break, and CONTINUE until the DESIRED Results are achieved.

Operating Steps

1) Push the 3-pin DIN Connector, which has the Infratonic Amplifier Power Supply/Transformer connected on the other end, into the Jack labeled 'POWER PACK' on the Rear of the Infratonic Amplifier, being SURE to MATCH-UP the Pins with the Jack's Receptacles.

2) Plug the Infratonic Amplifier Power Supply/Transformer into the SAME Power Strip that the WAVESHAPER™ Frequency Instrument is plugged into and then rock the Power Switch to turn the Power Strip "ON".
NOTE: Your WAVESHAPER™ Frequency Instrument should be plugged into a HIGH Quality Surge Suppressor Power Strip (i.e.- Tripp-Lite - 600 joules), thus ensuring SAFE and EFFICIENT Operation.
The Cooling Fan on the Infratonic Amplifier is NOW turned "ON" and it's Speed will VARY, according to the 'POWER' Knob Setting (see Step 11).

3) Push the Red & Black Banana Plugs on the 12 in. Y-Cable, which has a 1/8" Plug connected to the other end, into the corresponding Red & Black Banana Jacks on the Left Side of the Front Panel of your WAVESHAPER™ Frequency Instrument.

4) Push the 1/8" Plug, which is connected to one end of the 12 in. Y-Cable, into the 1/8" Jack labeled 'SOURCE' on the Infratonic Amplifier.

5) Push the 1/8" Plug, which is connected to the BIOMAGNESONIC TRANSDUCER II™, into the 1/8" Jack, which is connected to the 25' Coiled Cord, and then push the RCA Plug, which is connected to the other end of the 25' Coiled Cord, into the RCA Jack labeled 'OUT' on the front of the Infratonic Amplifier.

6) Turn the OUTPUT LEVEL Control + OFF/ON Switch on the WAVESHAPER™ Frequency Instrument CLOCKWISE just past the "Snapping" Sound to turn the Power "ON".
NOTE: Please WAIT at least 15 mins. after the Power is "ON" to allow your WAVESHAPER™ Frequency Instrument time to WARM-UP and STABILIZE. It won't be necessary to WAIT AGAIN, after this initial 15 mins., if using MORE than one SPECIFIC Frequency.

7) Push the Black SINE/SQUARE Slide Switch on the Left Side of the Front Panel of your WAVESHAPER™ Frequency Instrument to SQUARE.
NOTE: You can also try the SINE Wave, when doing your Experimental Treatments.

8) Follow the Steps in the WAVESHAPER™ Frequency Instrument - Operating Instructions to use ANY of the following Tuning Methods that you prefer: Ia - TUNING Knob/Single Frequency Operation, Ib - TUNING Knob/Dual Frequency Operation, IIa - Keypad/Single Frequency Operation or IIa - Keypad/Dual Frequency Operation.
NOTE: Proceed with Step 10 of these Operating Instructions, when you have keyed in the SPECIFIC Frequency (see Frequency Manual). Repeat this Step for each SPECIFIC Frequency (see Frequency Manual) of your EXPERIMENTAL Treatment Session.
NOTE: Start with the LOWEST SPECIFIC Frequency (i.e. - 1.0 Hz., 5.0 Hz.,....) on the Frequency Charts that you NEED to use.

9) Turn the 'POWER' Control Knob on the Infratonic Amplifier CLOCKWISE until you hear a "Snapping" Sound to turn the Power "ON".

10) Turn the OUTPUT LEVEL Knob on the WAVESHAPER™ Frequency Instrument CLOCKWISE to the 12 o'clock Position, if you're using the BIOMAGNESONIC TRANSDUCER II™ in the Frequency Range of 1 Hz. to 500 Hz. (3 o'clock - 500 Hz. to 3000 Hz.), and allow it to REMAIN at this Setting throughout your EXPERIMENTAL Treatment Session for OPTIMAL Results.

11) Turn the 'POWER' Control Knob on the Infratonic Amplifier CLOCKWISE up to the MAXIMUM Position, before the Sound from the BIOMAGNESONIC TRANSDUCER II™ begins to DISTORT and/or becomes LOWER.
NOTE: This MAXIMUM Setting may need to be CHANGED, depending on the SPECIFIC Frequency Frequency Chart & Frequency Chart 2), that is being used.

12) Hold onto the Handles of the BIOMAGNESONIC TRANSDUCER II™ and place it on the Body Area (see Frequency Chart 1 or Frequency Chart 2), which NEEDS to be treated.
NOTE: The BIOMAGNESONIC TRANSDUCER II™ should be placed on BARE Skin for OPTIMAL Results, but can placed on THIN Clothing. If there is ANY DISCOMFORT felt, then move it to another Area, which is CLOSE to the Area, that is being treated.

13) Turn the OUTPUT LEVEL Knob on your WAVESHAPER™ Frequency Instrument COUNTER-CLOCKWISE, when FINISHED with the FIRST Frequency and then REPEAT Steps 8 - 12 for each SPECIFIC Frequency (see Frequency Chart 1 &/or Frequency Chart 2) until your Experimental Treatment is COMPLETED.

14) Turn the OUTPUT LEVEL Control + OFF/ON Switch on the WAVESHAPER™ Frequency Instrument COMPLETELY COUNTER-CLOCKWISE, just past the "Snapping" Sound, to turn the Power "OFF".

15) Turn the 'POWER' Knob on the Infratonic Amplifier COUNTER-CLOCKWISE, just past the "Snapping" Sound, to turn the Power "OFF".

NOTE: If DETOXIFICATION becomes TOO UNCOMFORTABLE or ANY ADVERSE Reactions occur, then DISCONTINUE &/or MODIFY the Experimental Treatment, and if possible, try to continue this Experimental Electromagnetic & Sound Therapy Treatment.

Revised 1/21/08