BIOMAGNESONIC TRANSDUCER XL™ - Operating Instructions

DISCLAIMER: TOTAL HEALTH ASSOCIATES makes NO SPECIFIC Medical Claims for the BIOMAGNESONIC TRANSDUCER XL™, and does NOT dispense Medical Advice. The BIOMAGNESONIC TRANSDUCER XL™ is NOT registered as a Medical Device with the U.S. Food and Drug Administration and is to be used "FOR EXPERIMENTAL USE ONLY". Please consult your Physician regarding ANY undiagnosed Condition or before ENHANCING your Treatment with this EXPERIMENTAL Biomagnetic, Electromagnetic, Sonic & Pressure Wave Therapy.

CAUTION - The BIOMAGNESONIC TRANSDUCER XL™ should never be used with a Frequency LOWER than 5 Hz., while driving a Vehicle to AVOID the DANGER of falling ASLEEP at the Wheel.
The BIOMAGNESONIC TRANSDUCER XL™ can produce Sound Frequencies, which tend to dissolve Blood Clots. Therefore, this Unit should NOT be used in the following circumstances:
(1) on anyone, who has a Phlebitis.
(2) on anyone, who has Thrombosis, especially using 10 Hz..
(3) on anyone, who has NOT had several weeks of GOOD Healing after Major or Minor Surgery.
(4) on anyone, who has suffered a Stroke, which was caused by an Artery rupturing in the Brain.

or in the following circumstances:
(1) on anyone, who is Pregnant or is suspected of being Pregnant.
(2) on anyone, who has Epilepsy &/or Convulsions.
(3) on anyone, who has a Psychotic Disorder.
(4) on anyone, who has Glaucoma.
(5) on anyone, who has Back Problems.
(6) on anyone, who has Hypertension with resistance to Medical Therapy.
(7) on anyone, who has Heart Problems, especially using 1 Hz..
(8) on anyone, who wears a Pacemaker &/or a Defibrillator, especially using 1 Hz..
(9) on anyone near skeletal degenerative disorders.
(10) on anyone on the stomach region at 7 Hz..

Preliminary Comments

1) Before starting your EXPERIMENTAL Treatment Session, please be SURE that you've read and understand your WAVESHAPER™ Frequency Instrument - Operating Instructions, plus DISCLAIMER and CAUTION in the Box at the top of this page.

2) Please ELIMINATE Steps 1 - 8 in the following Operating Steps, once they are COMPLETED the FIRST Time, if you're using your BIOMAGNESONIC TRANSDUCER XL™ on a regular basis.

3) Push, if necessary, the Low Cut and Phase Buttons, so that they are both in the 'OUT' position, and allow them to remain indefintely in this position. Now turn, if necessary, the Volume knob fully counter-clockwise to the FIRST dot, so that you will later be ABLE to obtain OPTIMAL Results from your Professional Infratonic Amplifier (AudioSource Amp 5.1A Monoblack Amplifier).

4) Perform the following Procedure 2-3 times per day for a TOTAL Experimental Treatment Time per Session of 15/20 mins..
NOTE: INCREASE your TOTAL Experimental Treatment Time on the 2nd Week to 20 mins. (Acute) & 25 mins. (Chronic), on the 3rd week to 25/30 mins. and on the 4th week to 30/35 mins..

5) Perform your Experimental Treatments 1 - 2 times daily (morning &/or evening - total time - 1 hr.) for 6 consecutive days, then NONE on the 7th day, REPEATING the SAME Cycle for 2 MORE weeks and then DISCONTINUE for 1 week. If the DESIRED Results have NOT been achieved, then REPEAT your Experimental Treatments after the 1 week break, and CONTINUE until the DESIRED Results are achieved.

Operating Steps

1) Push the 3-pin Female A.C. Power Jack, which is connected to one end of the A.C. Power Cable, and which has the 3-pin Male A.C. Power Plug connected to the opposite end, into the Male A.C. Power Jack on the lower right-hand corner of the rear panel of your Professional Infratonic Amplifier (AudioSource Amp 5.1A Monoblack Amplifier).

2) Push the 3-pin Male A.C. Power Plug, which is connected to the opposite end of the A.C. Power Cable, and which has 3-pin Female A.C. Power Jack connected to the Male A.C. Power Jack on the lower right-hand corner of the rear panel of your Professional Infratonic Amplifier, into the SAME Power Strip that your WAVEFORMER XL™ Frequency Instrument is plugged into and then rock/push the Power Switch to turn the Power Strip "ON".
NOTE: Your WAVESHAPER™ Frequency Instrument should be plugged into a HIGH Quality Surge Suppressor Power Strip (i.e.- Tripp-Lite - 600 joules), thus ensuring SAFE and EFFICIENT Operation.

3) Push the BNC Plug, which is connected to one end of a 1 ft. cable, and which has another BNC Plug connected to the opposite end, onto the BNC Jack at the lower right-hand corner of the front panel of your WAVEFORMER XL™ Frequency Instrument.

4) Push the other BNC Plug, which is connected to the opposite end of the 1 ft. cable, which has the above BNC Plug connected to your WAVEFORMER XL™ Frequency Instrument, into the BNC Jack at one end of the Impedance Match Box (black plastic box).

5) Push the gold RCA Plug, which is connected to one end of the 3 ft. Cable, and which has another gold RCA Plug connected to the opposite end, into the RCA Jack, which is on opposite end of the Impedance Match Box (black plastic box).

6) Push the other gold RCA Plug, which is connected to opposite end of the 3 ft. Cable, and which has another gold RCA Plug connected to the Impedance Matchbox, into the RCA Jack on the the upper right-hand corner of the rear panel of your Professional Infratonic Amplifier.

7) Push the Red & Black pin plugs, which are connected to one end of the 25 ft. Heavy-Duty Coiled Cable, and which has the Red & Black Banana Plugs connected to the opposite end, into Red and Black speaker terminals of your Professional Infratonic Transducer (AURA Bass Shaker Model No. AST-2B-04).

8) Push the red & black banana plugs, which are connected to the opposite end of the 25 ft. Heavy-Duty Coiled Cable and which has the other end connected to the Professional Infratonic Transducer (AURA Bass Shaker Model No. AST-2B-04), into the red & black banana jacks, which are labeled 'Speaker' and which are located on the upper left-hand corner of the rear panel of your Professional Infratonic Amplifier.

9) Rock the POWER Switch to the upper position on your Professional Infratonic Amplifier to turn the Power "ON".

10) Push the POWER Button 'IN' on your WAVESHAPER™ Frequency Instrument to turn the Power "ON".
NOTE: Please wait at least 5 mins. after the Power is "ON" to allow your WAVESHAPER™ Frequency Instrument time to WARM-UP and STABILIZE. It won't be necessary to WAIT AGAIN, after this initial 5 mins., if using MORE than one SPECIFIC Frequency.

11) Push the WAVE button, which is located on the upper right-hand corner of the digital display of your WAVESHAPER™ Frequency Instrument, until you see the Sine (smooth) Waveform shown on the display.

12) Follow Steps 6, 7 & 8 in your WAVESHAPER™ Frequency Instrument - Operating Instructions to key in a SPECIFIC Frequency.
NOTE: Proceed with Step 13 of these Operating Instructions, when you have keyed in the SPECIFIC Frequency (see Frequency Chart 1 or Frequency Chart 2). Repeat this Step for each SPECIFIC Frequency of your EXPERIMENTAL Treatment Session.
NOTE: Start with the LOWEST SPECIFIC Frequency (i.e. - 1.0 Hz., 5.0 Hz.,....) on the Frequency Charts, that you want to use.

13) Turn the AMPL control knob on your WAVESHAPER™ Frequency Instrument CLOCKWISE to the 9 o'clock position, if you're using the BIOMAGNESONIC TRANSDUCER XL™ with frequencies ranging from 1 Hz. to 500 Hz. (12 o'clock - 500 Hz. to 5000 Hz.), and allow it to REMAIN at this position(s) throughout your EXPERIMENTAL Sound Therapy Treatment Session for OPTIMAL Results.

14) Turn the click-type Volume control knob on your Professional Infratonic Amplifier slowly CLOCKWISE until the red 'Peak' Light just begins to light-up and then turn back one click and/or until the red 'Peak' Light goes-out.
NOTE: This MAXIMUM setting will probably need to be changed, depending on the SPECIFIC Frequency Frequency Chart 1 & Frequency Chart 2), that you're using.

15) Hold onto the top of the Handles of your Professional Infratonic Transducer and then place it on the Body Area (see Frequency Chart 1 or Frequency Chart 2), that you want to treat.
NOTE: Your Professional Infratonic Transducer should be placed on BARE Skin for OPTIMAL Results, but can placed on THIN Clothing. If you feel ANY DISCOMFORT, then move it to another Area, which is CLOSE to the Area, that you want to treat.

16) Turn the AMPL Knob on your WAVESHAPER™ Frequency Instrument COMPLETELY COUNTER-CLOCKWISE, when FINISHED with your FIRST Frequency and then REPEAT Steps 12 - 15 for each SPECIFIC Frequency (see Frequency Chart 1 &/or Frequency Chart 2) until your EXPERIMENTAL Sound Therapy Treatment session is COMPLETED.
NOTE: You may want to try the frequency of 72 Hz., since it's an Experimental Frequency, that's being used by U.S. Medical Researchers to RESTORE and HEAL deep Tissue.

FINAL STEPS

When you have FINISHED your EXPERIMENTAL Sound Therapy Treatment session, then please COMPLETE the following steps:

1) Turn the AMPL (amplitude/volume) control knob on your WAVESHAPER™ Frequency Instrument COMPLETELY COUNTER-CLOCKWISE.

2) Push the POWER Button 'IN' again on your WAVESHAPER™ Frequency Instrument to turn the Power "OFF".

3) Turn the Volume Control on your Professional Infratonic Amplifier COMPLETELY COUNTER-CLOCKWISE.

4) Rock the POWER Switch to the lower position on your Professional Infratonic Amplifier to turn the Power "OFF".

5) Continue these Experimental Sound Therapy Treatments until you obtain the desired results.

NOTE: If DETOXIFICATION becomes TOO UNCOMFORTABLE or ANY ADVERSE Reactions occur, then DISCONTINUE &/or MODIFY the Experimental Treatment, and if possible, try to continue this Experimental Electromagnetic & Sound Therapy Treatment again.
Drink at least 3-5 glasses of Charcoal Slurry per day during the treatment period and especially during the time-off period.

Revised 2/13/08